Fit your Brummstadt screen to a Toyota HiAce H200 (2004 to 2019)
Fit the Brummstadt screen to your HiAce yourself, one step at a time, and test everything while the dash is still open.
- Time
- About 27 minutes to watch. First time, give yourself one to three hours to fit it; done it before, it's often done in under an hour.
- Have ready
- Plastic trim tools, a Phillips screwdriver, a spanner for the battery clamp, a few cable ties and some tape, and a multimeter if you're fitting a camera.
- Two frames
- Your box holds a big frame and a small frame. Three quick looks at your dash tell you which one goes in: the colour of the trim, the pocket left of the radio, and the trim panel towards the steering wheel.
- How to watch
- Watch it once all the way to the end first, because the end holds a few extra tips. Then start again and follow along step by step, pausing whenever you like.
Does this video fit your car?
One video for the four dash options and both frames of the HiAce 200 Series. Check these points before you start.
- Your van
- This video is for the Toyota HiAce 200 Series, built from 2004 to 2019, with the Brummstadt 10.1 inch screen.
- Your dash option
- On the product page you pick one of four dash options, from two easy looks. Is the trim around your radio silver, or is it dark grey? And is there an open pocket just to the left of the radio? That gives Silver Trim Stereo Only, Silver Trim Stereo + Left Storage Pocket, Dark Trim Stereo Only or Dark Trim Stereo + Left Storage Pocket.
- Big or small frame
- Your kit is made to fit both styles of HiAce dash, with a big frame that runs right across to the steering wheel and a small frame that sits straight into the original radio opening. Follow your trim panel from the radio towards the steering wheel. If it stops short of it, with its own small piece around the steering column, the small frame is the one. In our customers' vans, the small frame in the original panel has given the cleanest result, so if you're in any doubt, that's the one.
- Dark trim or pocket
- With the open pocket, or the dark trim, the small frame is your frame too. The big frame only comes in silver, and the small one comes in silver or matte black. Your pocket and your own trim stay just as they are.
- Wide body
- Do you drive a wide-body HiAce, like the super long wheelbase or the Grand Cabin? Then it's the small frame as well, because the big frame is made for the standard dash.
- Japanese imports
- A Japanese import built after 2019 that still has this dash shape, like the GDH201, 206 or 226, takes this kit, and this video is for it too. Go by the dash shape you see in front of you. Some imports have five factory radio plugs instead of three, so compare them with your new harness, shape by shape.
- Factory radio
- It doesn't matter whether your HiAce has the factory CD radio or the factory touchscreen. The way out is the same: the upper panel comes off, and the radio sits on its side brackets underneath.
- What stays
- Your climate knobs stay, and your hazard switch sits right under the new screen. Nothing in the dash gets cut.
- Steering wheel buttons
- If your HiAce has steering wheel buttons, they keep working. There's no extra box for them on the 200 Series: your Brummstadt unit learns them instead, and it takes about a minute. Not every 200 Series has steering wheel buttons, and without them you control the volume on the screen.
- Factory camera
- If your reverse camera shows in the rear-view mirror, it stays there and keeps working, and your Brummstadt camera shows on the big screen. A factory camera that showed on the old touchscreen can work on your new screen if it runs on 12 volts and you pick its format, usually DSV. Some Toyota cameras run on about 6 volts, and then a 12 to 6 volt step-down module in its power lead, or the Brummstadt camera, is the way.
- Not in this video
- The HiAce 300 Series, the new shape that arrived in 2019, takes a different kit and has its own installation video.
What you need
- Tools
- Plastic trim tools
- A Phillips screwdriver
- A spanner for the battery clamp
- A few cable ties and some tape
- For a camera: a multimeter
- Time
- First time, give yourself one to three hours. Done this before? Then it's often done in under an hour.
- In the box
- Your Brummstadt screen, already fitted in the big frame
- The small frame
- The plug-in harness
- A small aerial booster
- The GPS aerial
- Any camera, microphone or other extras you picked
- Good to have
- A towel to lay every part out on, so anything missing shows up now, and another on the passenger seat for the panel you take off.
Optional parts
Each one has its own page, and you can also add it on the kit page when you order.
- Trim removal toolsFour plastic pieces that take the trim off without scratches.
- Rear cameraAHD 1080p reverse camera with night vision. It comes on when you select reverse.
- Front cameraAHD 1080p forward view camera with night vision. It has its own input on the unit and comes on by itself when you drive forward.
- Rear camera extension cableA 10 m extension: the camera cable in the kit is 3 m, and in a long HiAce the route from the back door to the dash can be much longer.
- External microphoneA hands-free mic on the roof lining beside the driver's sun visor, so callers hear you and not the road.
- DAB+ digital radio adapterDigital radio from a USB lead on the unit, with a strip aerial on the windscreen.
- Tyre pressure sensors (TPMS)Kits with 4 or 8 sensors, external or internal, talking to the unit through their own small USB receiver. Internal sensors are fitted at a tyre shop.
- OBD2 diagnostic toolA Bluetooth reader for the diagnostic port: live engine data and fault codes.
Step by step
The same steps as the video. Each one plays from its own spot.
Which option is yours
Play from 1:20- The 200 Series came with a few different dashes, and on our product page you picked one of four dash options. Here they are side by side in the video, so you can match your own dash to the right one.
- There are two easy looks. First, is the trim around your radio silver, or is it dark grey? Second, is there an open pocket just to the left of the radio?
- Silver trim with no pocket is the option called Silver Trim Stereo Only. Silver trim with the pocket is Silver Trim Stereo + Left Storage Pocket.
- It works the same way with the dark ones. Dark trim with no pocket is Dark Trim Stereo Only, and dark trim with the pocket is Dark Trim Stereo + Left Storage Pocket.
- There are two frames in your box, a big one and a small one. Your kit is made to fit both styles of HiAce dash. The big frame comes in two parts: a radio part with your screen already fitted, and a long trim strip, and together they run right across to the steering wheel. The small frame sits straight into the original radio opening, and your own trim stays where it is.
- The big frame reaches across to the steering wheel trim and carries the vent surrounds, and the small frame only fills the radio opening.
- Here's the third look, and it's the one that decides it. Follow your trim panel from the radio towards the steering wheel. Does it run all the way across without a break? Or does it stop short of it, with its own small piece around the steering column?
- If it runs all the way to the steering wheel, the big frame is made for your dash. If it stops short, the small frame is the one, because the big frame can't reach past your own small piece by the column.
- In our customers' vans, the small frame in the original panel has given the cleanest result, so if you're in any doubt, that's the one.
- Have you got the open pocket, or the dark trim? Then the small frame is your frame too. The big frame only comes in silver, and the small one comes in silver or matte black. It sits in the radio opening, and your pocket and your own trim stay just as they are.
- Do you drive a wide-body HiAce, like the super long wheelbase or the Grand Cabin? Then it's the small frame as well, because the big frame is made for the standard dash.
- Is your HiAce a Japanese import that was built after 2019, but still has this dash shape, like the GDH201, 206 or 226? Then this video is yours, and so is this kit. Go by the dash shape you see in front of you.
- So that's one look at the colour, one at the pocket, and one along to the steering wheel. In thirty seconds you know exactly which frame you're fitting today.
- In your box you'll find your Brummstadt screen, already fitted in the big frame, the small frame and the plug-in harness. There's also an aerial booster, and any camera, microphone or other extras you picked come in the same box.
- The memory and storage version you picked doesn't change a single step.
- At the end, there's a big bright screen in a frame that matches your dash, with a harness behind it that plugs straight into your car's own plugs. Nothing in the dash gets cut.
Before you start
Play from 5:33- Our one rule for the whole install is feel, not force. If something won't move, there's a reason.
- Lay every part out on a towel first, so anything missing shows up now and not halfway through. Put another towel on the passenger seat for the panel you'll take off.
- You'll need plastic trim tools and a Phillips screwdriver. Add a spanner for the battery clamp, plus a few cable ties and some tape. If you're fitting a camera, a multimeter makes it easy.
- Why plastic tools? Because a metal screwdriver leaves marks in the soft trim for good. A plastic tool slides in, and the panel comes away clean.
- Take a photo of your dash now, and later another of the back of the old radio before you unplug anything. On a Japanese import that second photo matters even more, because its plugs can look different, and the photo lets you compare them in a moment.
- Last, try the old system once. Play the radio, press the steering wheel buttons, flash the hazards and look at the reverse camera, so you know what normal looks like.
- Next is the battery. Switch the ignition and the lights off, then undo the negative terminal, the one marked minus, and tuck the lead aside in a cloth.
- With the battery connected, a bare pin touching metal can blow a fuse, and then the screen stays dark on the day. A minute with a spanner saves you an afternoon.
Remove the factory head unit
Play from 7:26- Here's how the HiAce comes apart. The radio sits behind one long upper panel that runs from the passenger door across to the instrument cluster, and that panel carries the air vents. It lifts off in one piece, and then the radio is right there.
- It doesn't matter whether your HiAce has the factory CD radio or the factory touchscreen. The way out is the same: the upper panel comes off, and the radio sits on its side brackets underneath.
- Open the top glovebox on the passenger side, so you can see the panel's edge from inside and reach it easily.
- Start at the passenger end, right next to the door. Slide a plastic tool into the gap, and ease the panel out until the first clips let go.
- Then work along the lower edge towards the radio, one clip at a time, with the tool right next to each clip.
- Lever in one spot, or yank the whole panel at once, and a clip snaps or the plastic cracks, and then that panel rattles for good. Go clip by clip, and each one lets go with a small pop.
- When the lower edge is free, lift the panel up and towards you, and rest it against the windscreen. Along its back edge you'll see a row of clips, and under it the metal frame of the dash.
- If it won't lift, look before you pull harder, because something is still holding it. Look along the edges, find the clip or fixing that's still in, free it, and the panel comes.
- The hazard switch doesn't come off with the panel. The strip with the hazard switch stays in the dash, under the radio. If you're fitting the big frame, the switch moves across in the next step.
- Now take out the old radio. It's held by Phillips screws on its metal side brackets. Undo them all, and tape each screw to a piece of paper, so none gets lost behind the dash.
- Slide the radio forward just far enough to reach the back, then unplug each plug. Press the tab first, then pull the plug body, never the wires.
- Pull on the wires instead, and a thin lead can tear out of its plug, with no slack left to fix it. Press the tab, pull the body, and it slides out easily.
- Is your HiAce a Japanese import, like a Regius Ace or a Grand Cabin? Then the back of its factory radio can look a little different, and some imports have five factory plugs instead of three. Compare them with the plugs on your new harness before you go on, shape by shape.
- The old radio's out. Keep it in a box with its brackets and screws: if you ever sell the HiAce, it can go back in.
Fit the frame
Play from 10:37- Before anything gets screwed in, hold your new frame up to the dash, with nothing plugged in yet. This trial fit takes a minute, and it tells you everything.
- With the big frame, check three things. It reaches all the way to the steering wheel, the vents line up with their openings, and the hazard switch lines up with its cut-out.
- The big frame brings new surrounds only. Your vents and the cup holder move across from the old panels, and so does your hazard switch.
- If you're not sure by eye, measure it. Run a tape along your dash from the radio opening to the steering wheel trim, then lay the tape along the big frame on your towel. If the big frame is longer than that space, the small frame is yours.
- If the big frame stops short of your steering wheel, or you'd have to cut your dash to make it fit, stop right there. Cut plastic leaves edges that never look right again. Put the small frame in instead: it sits in the radio opening, and it looks factory.
- With the small frame it's simpler. It goes straight into the original radio opening, and your own upper panel goes back on around it later.
- Your own hazard switch moves from the old strip into the big frame. Unplug it first, then fit it into the frame's cut-out so it sits firm and flush.
- Are you fitting the small frame? Then your screen moves across first. Undo the screws that hold it in the big frame, lift it out, and fit it into the small frame with the same screws, turning each one until it stops and then just a touch more.
- Keep them snug, not tight. If you over-tighten them, the metal screw cuts into the plastic frame, the frame bends, and then it won't sit flush again. Hand tight with a screwdriver is plenty.
Wiring and plugs
Play from 12:48- Now it's time for the plugs. Your Brummstadt harness has a partner for each of your car's main radio plugs. Click each car plug into its partner: every one has its own shape, like a kids' shape puzzle.
- Push until it clicks, then give the plug body a gentle tug. A half-latched plug drops out on the first bumpy road and takes the sound or the screen with it. And if a plug won't go in, check its shape, and never force it or cut it.
- Plugs left over are normal on a HiAce. Some plugs simply stay free. The square plug with the loose wires isn't used, and neither are the round sockets for aux in, audio out and the subwoofer, or the pink AMP-C wire. It's fine to have leftover plugs.
- On the car side, the factory plugs for GPS, Bluetooth or the old microphone have no partner either, because your Brummstadt unit has its own. Tape them up and tuck them away.
- Has your HiAce had an aftermarket radio before? Then there may be an old adapter harness between the car and the plugs. Take it out, so your new harness plugs straight into the car's own plugs. If it stays in, the plugs won't match.
- Your car's aerial plug goes into the black aerial plug on your harness, and that lead goes into the radio socket on the back of the unit.
- Your box also holds a small aerial booster. Next to the yellow power wire on your harness you'll find a wire labelled ANT, often blue. Join it to the blue lead of the booster with the joiner, and your stations come in strong.
- Leave that blue wire unconnected, and the radio may still play, but stations crackle or drop out. Connect it, and the reception comes back.
- Two little things are easy to miss. If there's a fan plug in that bundle of round plugs, it goes into its partner, so the unit stays cool. And the other loose blue wire, the one with the rubber cap and no label, stays capped, because nothing on your HiAce needs it.
- Your GPS aerial plugs into the socket marked GPS. Put the aerial up on top of the dash, under the plastic and away from metal, so it can see the sky.
- Did you order the external microphone? Plug it into the small round socket marked MIC on the bundle of round plugs. Run the lead up the windscreen pillar and stick the mic on the roof lining right beside the driver's sun visor, away from the vents, so callers hear you and not the road.
- Does your unit have a SIM holder? Fit your SIM now while everything's in your hands, and the unit gets mobile data without your phone.
- Did you pick DAB+? The DAB module runs from a USB lead on the unit, and its strip aerial goes on the windscreen.
- Did you pick the dash camera? It connects by USB, and you watch and control its footage right on the screen. And if you picked tyre pressure sensors, they talk to the unit through their own small USB receiver.
- The OBD2 tool plugs into the diagnostic port under the dashboard. It talks to the unit or your phone over Bluetooth, and it shows live engine data and fault codes.
- Then cable-tie the long leads together and to the car's own wiring. Loose leads rattle behind the dash, and in time an edge can rub through the insulation and cause a short. A few ties keep it quiet and safe.
Steering wheel buttons
Play from 17:01- On the 200 Series HiAce there's no extra box for the steering wheel buttons. Your Brummstadt unit learns them instead, and it takes about a minute.
- Not every 200 Series has steering wheel buttons. If yours doesn't, you control the volume on the screen instead: swipe up from the bottom edge, and the volume keys appear.
- You'll do it right after the first power-up. Open the learning app on the unit. Then press one button on your wheel, and tap the matching symbol on the screen. Do that for every button.
- If a button does nothing afterwards, simply run the learning again for that button: press it on your wheel, then tap its symbol.
Reverse camera
Play from 17:52- Here are the key steps for your HiAce, and our full camera video has every setting and check.
- Long van? Measure it first. The camera cable in your kit is three metres long, and in a long HiAce the route from the back door to the dash can be much longer: one owner's route came to nearly nine metres. Run a string the way the cable will go, and if it's short, the ten metre extension cable sorts it.
- Mount the Brummstadt camera on the back of the van, above the number plate. Run its lead inside along the roof lining or under the floor trim, through a rubber grommet, never over a sharp edge. Your rear parking sensors keep beeping just as before.
- Camera power comes from the reverse light. The trigger wire, usually brown and marked BACK or REVERSE, goes to the reverse light's positive wire, and the black one goes to bare metal. With a meter, you want 12 volts in reverse and nothing in park.
- Put the trigger on the indicator wire, and the camera jumps on every time you indicate. Check with the meter first, and the camera only comes up in reverse.
- At the dash, the camera's yellow video plug goes into the yellow camera socket on the harness. It doesn't go into the aux sockets, or into video in.
- Plug it into AUX, and the screen stays empty in reverse, even though everything else is right. Plug it into the camera socket instead, and the picture comes straight up.
- If your reverse camera shows in the rear-view mirror, it stays there and keeps working. Your Brummstadt camera shows on the big screen.
- Did your factory camera show on the old touchscreen? It can work on your new screen if it runs on 12 volts and you pick its format, usually DSV. The yellow camera adapter joins your car's camera plug to the yellow camera socket on the harness, but not every kit has one. Some Toyota cameras run on about 6 volts, and then a 12 to 6 volt step-down module in its power lead, or the Brummstadt camera, is the way.
- Did you order the front camera as well? It has its own input on the unit, and it comes on by itself when you drive forward. Its lead runs from the grille to the dash, so measure that route too. Our camera video shows its socket and the setting for two cameras.
First power-up and settings
Play from 20:43- Reconnect the negative terminal, snug the nut, and turn the ignition on. You'll see the Brummstadt logo, and then the home screen.
- If the screen stays black, take the battery off again and check that the main plug has really clicked. A plug that's nearly in is the first thing to check.
- If you ever notice a hot plug or a burning smell, switch the ignition off and disconnect the battery straight away, and check that plug before you power up again.
- Now teach the steering wheel buttons in the learning app: press a button on your wheel, then tap its symbol, one button after the other.
- For the radio, set the radio region to Australia. If stations are weak, raise the FM sensitivity in the radio settings, one step at a time.
- Now set up the camera. Shift into reverse with your foot on the brake. No signal is a good sign: the screen has seen reverse. Now hold your finger on the picture until a box pops up, pick AHD1080P-25Hz for the Brummstadt camera, and save.
- If you fitted the external mic, pick External Mic in the settings and set the mic gain to 7, just as our microphone video shows step by step.
- For your phone, open ZLINK, the app for CarPlay and Android Auto. Pair over Bluetooth for wireless, or plug in a data cable.
- When it all works, take a photo of each settings screen, so you can set it back quickly after an update.
Test before closing
Play from 22:39- Do ten minutes of testing first, because a fix takes seconds while the dash is open, and an evening once it's closed.
- Touch the screen everywhere, play a song you know and change the volume, and try a radio station you know.
- Press every steering wheel button. Make a real call, both ways, so you hear the microphone. Then connect your phone and start CarPlay or Android Auto.
- With your foot on the brake, select reverse, and the camera comes up. Out of reverse, your normal screen is back. Then try the indicators, left and right, and the screen should stay put.
- Switch the headlights on and check that the screen is still easy to read. Then try the hazards: they flash just like before.
- Turn the ignition off and on again, and your settings should still be there. If something isn't right, go back to its plug or its setting. It's nearly always one of those two.
Closing up and done
Play from 23:55- All working? Switch the ignition off, and take the battery off again, so nothing's live while the leads move.
- Feed the harness in behind the unit, every lead clear of edges and screw holes, and slide the screen and frame home.
- If the frame won't sit flat, something's caught behind it. Don't pull it down with the screws, because they'd crush a lead and bend the frame. Lift it, free the lead, and it sits flat on its own.
- Fix it with its screws, each one from its spot on your paper, snug and gentle.
- Now the long upper panel goes back. Lower it into place, line up the clips along the back edge first, then press along the lower edge with the flat of your hand until each clip clicks home.
- Put the battery back on for one last round. Listen to the sound, press the buttons, and check the camera and the hazards, because closing up can nudge a plug.
- The battery was off, so set the clock if it needs it. It only takes a minute, and then you're done.
- An extra tip: keep your settings photos in the glovebox. If anything ever needs a tweak, you've got everything in one place.
Questions from customers
Questions HiAce owners asked us, answered in the video.
There are two frames in my box. Which one goes in?
Follow your trim panel from the radio towards the steering wheel. If it runs all the way to the steering wheel, the big frame is made for your dash. If it stops short, with its own small piece around the steering column, the small frame is the one.
In our customers' vans, the small frame in the original panel has given the cleanest result, so if you're in any doubt, that's the one. Hold the frame up for a trial fit before anything gets screwed in.
See it in the video at 2:58I have a dark dash. Which frame is mine?
The small frame. The big frame only comes in silver, and the small one comes in silver or matte black.
It sits in the radio opening, and your own trim stays just as it is. The same goes for a dash with the open pocket left of the radio.
See it in the video at 3:40My HiAce is a super long wheelbase. Which frame fits?
On a wide-body HiAce, like the super long wheelbase or the Grand Cabin, it's the small frame, because the big frame is made for the standard dash.
See it in the video at 3:59My HiAce is a Japanese import built after 2019. Is this the right kit?
If it still has this dash shape, like the GDH201, 206 or 226, this kit and this video are yours. Go by the dash shape you see in front of you.
The back of an import's factory radio can look a little different, and some imports have five factory plugs instead of three. Take a photo of it before you unplug anything, and compare them with the plugs on your new harness, shape by shape.
See it in the video at 4:12Will my steering wheel buttons still work?
Yes. On the 200 Series there's no extra box for them: your Brummstadt unit learns them right after the first power-up. Open the learning app, press one button on your wheel, and tap the matching symbol on the screen. Do that for every button.
If a button does nothing afterwards, simply run the learning again for that button. And if your HiAce has no steering wheel buttons, you control the volume on the screen: swipe up from the bottom edge, and the volume keys appear.
See it in the video at 17:02I've got plugs left over. Did I miss something?
That's normal on a HiAce. The square plug with the loose wires isn't used, and neither are the round sockets for aux in, audio out and the subwoofer, or the pink AMP-C wire.
On the car side, the factory plugs for GPS, Bluetooth or the old microphone have no partner either, because your Brummstadt unit has its own. Tape them up and tuck them away.
See it in the video at 13:23The radio crackles or drops out. What do I check?
Look for the wire labelled ANT, often blue, next to the yellow power wire on your harness. Join it to the blue lead of the aerial booster from your box. Leave it unconnected, and stations crackle or drop out.
Then set the radio region to Australia, and if stations are weak, raise the FM sensitivity in the radio settings, one step at a time.
See it in the video at 14:28The camera shows No signal, or nothing in reverse. What now?
No signal is a good sign: the screen has seen reverse. Hold your finger on the picture until a box pops up, pick AHD1080P-25Hz for the Brummstadt camera, and save.
If the screen stays empty in reverse, check that the camera's yellow video plug is in the yellow camera socket on the harness, not in AUX or video in, and that the trigger wire goes to the reverse light's positive wire.
See it in the video at 21:44After fitting
Once the screen is in and tested, these videos help you set up the rest. The installation video points to them along the way.
- Connect your phone to your Brummstadt unitZLINK for Apple CarPlay and Android Auto: pair over Bluetooth for wireless, or plug in a data cable. Video, 9:44.
- Reverse camera, sorted: camera format and wiring on your Brummstadt unitEvery camera setting and check, including the socket and the setting for a front camera. Video, 8:28.
- Clear calls on your Brummstadt unit: fitting the mic and the mic settingsIf you fitted the external mic: pick External Mic and set the mic gain. Video, 8:30.
- TPMS on your Brummstadt unitIf you added tyre pressure sensors: they talk to the unit through their own small USB receiver. Video, 8:45.
Prefer a professional fit?
Brummstadt also offers a professional fit: your kit fitted, programmed and tested at a partner workshop on the Gold Coast in Queensland or in Launceston in Tasmania. Choose Professional installation on the kit page when you order, with at least 28 days notice.
See the professional fitDid this video help?
Thank you for letting us know.
Thank you. If something was missing, ask us below.
Ask a question about this video
Your question comes straight to the Brummstadt team and is not shown on this page. We answer by email, and the questions we get help us make this video and its steps even better.
The kit in this video
Toyota HiAce 200 Series head unit kit
The kit in this video, with the 10.1 inch screen and both frames.
See the kitMore Toyota HiAce 200 Series videos
Connect your phone to your Brummstadt unitVideo, 9:44
RAM and storage on your Brummstadt unitVideo, 8:45
TPMS on your Brummstadt unitVideo, 8:45
Reverse camera, sorted: camera format and wiring on your Brummstadt unitVideo, 8:28
The 10 m rear camera extension cable: connecting it and routing itVideo, 1:32
Clear calls on your Brummstadt unit: fitting the mic and the mic settingsVideo, 8:30
How to update your Brummstadt head unit onlineVideo, 8:28
Full transcript
- Viewer: Can a big Android screen really go into my HiAce? Will my steering wheel buttons still work? And which frame is the right one for my dash?
- Narrator: Yes, it fits. Today you'll put a Brummstadt ten point one inch screen into your Toyota HiAce, the two hundred series built from two thousand and four to twenty nineteen, and it'll look like it came from the factory.
- Narrator: If your HiAce has steering wheel buttons, they keep working. Your climate knobs stay, and your hazard switch sits right under the new screen.
- Narrator: Is it your first time? Then give yourself one to three hours. Have you done this before? Then it's often done in under an hour. Put the kettle on, there's no rush.
- Narrator: Watch it once all the way to the end first, with your hands in your pockets, because the end holds a few extra tips. Then start again and follow along step by step, pausing whenever you like.
- Narrator: Here's the plan. We find your option, get ready and remove the factory head unit. Then we fit the frame, do the wiring and plugs, and teach the steering wheel buttons. We add the reverse camera, power up, test, and close it up.
- Narrator: The two hundred series came with a few different dashes, and on our product page you picked one of four dash options. Here they are side by side, so you can match your own dash to the right one.
- Narrator: There are two easy looks. First, is the trim around your radio silver, or is it dark grey? Second, is there an open pocket just to the left of the radio?
- Narrator: Silver trim with no pocket is the option called Silver Trim Stereo Only. Silver trim with the pocket is Silver Trim Stereo plus Left Storage Pocket.
- Narrator: It works the same way with the dark ones. Dark trim with no pocket is Dark Trim Stereo Only, and dark trim with the pocket is Dark Trim Stereo plus Left Storage Pocket.
- Viewer: There are two frames in my box, a big one and a small one. Which one goes in?
- Narrator: That's a good question. Your kit is made to fit both styles of HiAce dash. The big frame comes in two parts: a radio part with your screen already fitted, and a long trim strip, and together they run right across to the steering wheel. The small frame sits straight into the original radio opening, and your own trim stays where it is.
- Narrator: Here they are side by side, drawn to the same scale. The big frame reaches across to the steering wheel trim and carries the vent surrounds, and the small frame only fills the radio opening.
- Narrator: Here's the third look, and it's the one that decides it. Follow your trim panel from the radio towards the steering wheel. Does it run all the way across without a break? Or does it stop short of it, with its own small piece around the steering column?
- Narrator: If it runs all the way to the steering wheel, the big frame is made for your dash. If it stops short, the small frame is the one, because the big frame can't reach past your own small piece by the column.
- Narrator: In our customers' vans, the small frame in the original panel has given the cleanest result, so if you're in any doubt, that's the one.
- Narrator: Have you got the open pocket, or the dark trim? Then the small frame is your frame too. The big frame only comes in silver, and the small one comes in silver or matte black. It sits in the radio opening, and your pocket and your own trim stay just as they are.
- Narrator: Do you drive a wide-body HiAce, like the super long wheelbase or the Grand Cabin? Then it's the small frame as well, because the big frame is made for the standard dash.
- Narrator: Is your HiAce a Japanese import that was built after twenty nineteen, but still has this dash shape, like the GDH two oh one, two oh six or two two six? Then this film is yours, and so is this kit. Go by the dash shape you see in front of you.
- Narrator: Look at your own dash. This table puts it all in one place.
- Narrator: So that's one look at the colour, one at the pocket, and one along to the steering wheel. In thirty seconds you know exactly which frame you're fitting today.
- Narrator: So in your box you'll find your Brummstadt screen, already fitted in the big frame, the small frame and the plug-in harness. There's also an aerial booster, and any camera, microphone or other extras you picked come in the same box.
- Narrator: The memory and storage version you picked doesn't change a single step. To see what it gives you, tap here for our RAM and storage film.
- Narrator: And at the end, this is what sits in your HiAce: the big bright screen in a frame that matches your dash, with a harness behind it that plugs straight into your car's own plugs. Nothing in the dash gets cut.
- Narrator: Our one rule for the whole install is feel, not force. If something won't move, there's a reason, and we'll show you what it is.
- Narrator: Lay every part out on a towel first, so anything missing shows up now and not halfway through. Put another towel on the passenger seat for the panel you'll take off.
- Narrator: You'll need plastic trim tools and a Phillips screwdriver. Add a spanner for the battery clamp, plus a few cable ties and some tape. If you're fitting a camera, a multimeter makes it easy.
- Narrator: Why do we use plastic tools? Because a metal screwdriver leaves marks in the soft trim for good. A plastic tool slides in, and the panel comes away clean.
- Narrator: Take a photo of your dash now, and later another of the back of the old radio before you unplug anything. On a Japanese import that second photo matters even more, because its plugs can look different, and the photo lets you compare them in a moment.
- Narrator: Last, try the old system once. Play the radio, press the steering wheel buttons, flash the hazards and look at the reverse camera, so you know what normal looks like.
- Narrator: Next is the battery. Switch the ignition and the lights off, then undo the negative terminal, the one marked minus, and tuck the lead aside in a cloth.
- Viewer: Do I really need to? It's only a radio.
- Narrator: That's a fair question. With the battery connected, a bare pin touching metal can blow a fuse, and then the screen stays dark on the day. A minute with a spanner saves you an afternoon.
- Narrator: Here's how the HiAce comes apart. The radio sits behind one long upper panel that runs from the passenger door across to the instrument cluster, and that panel carries the air vents. It lifts off in one piece, and then the radio is right there.
- Narrator: It doesn't matter whether your HiAce has the factory CD radio or the factory touchscreen. The way out is the same: the upper panel comes off, and the radio sits on its side brackets underneath.
- Narrator: Open the top glovebox on the passenger side, so you can see the panel's edge from inside and reach it easily.
- Narrator: Start at the passenger end, right next to the door. Slide a plastic tool into the gap, and ease the panel out until the first clips let go.
- Narrator: Then work along the lower edge towards the radio, one clip at a time, with the tool right next to each clip.
- Narrator: Lever in one spot, or yank the whole panel at once, and a clip snaps or the plastic cracks, and then that panel rattles for good. Go clip by clip, and each one lets go with a small pop.
- Narrator: When the lower edge is free, lift the panel up and towards you, and rest it against the windscreen. Along its back edge you'll see a row of clips, and under it the metal frame of the dash.
- Narrator: If it won't lift, look before you pull harder, because something is still holding it. Look along the edges, find the clip or fixing that's still in, free it, and the panel comes.
- Viewer: Does the hazard switch come off with the panel?
- Narrator: No, it doesn't come off. The strip with the hazard switch stays in the dash, under the radio. If you're fitting the big frame, we'll move the switch across in the next chapter.
- Narrator: Now let's take out the old radio. It's held by Phillips screws on its metal side brackets. Undo them all, and tape each screw to a piece of paper, so none gets lost behind the dash.
- Narrator: Slide the radio forward just far enough to reach the back, then unplug each plug. Press the tab first, then pull the plug body, never the wires.
- Narrator: Pull on the wires instead, and a thin lead can tear out of its plug, with no slack left to fix it. Press the tab, pull the body, and it slides out easily.
- Narrator: Is your HiAce a Japanese import, like a Regius Ace or a Grand Cabin? Then the back of its factory radio can look a little different, and some imports have five factory plugs instead of three. Compare them with the plugs on your new harness before you go on, shape by shape.
- Narrator: The old radio's out. Keep it in a box with its brackets and screws: if you ever sell the HiAce, it can go back in.
- Narrator: Before anything gets screwed in, hold your new frame up to the dash, with nothing plugged in yet. This trial fit takes a minute, and it tells you everything.
- Narrator: With the big frame, check three things. It reaches all the way to the steering wheel, the vents line up with their openings, and the hazard switch lines up with its cut-out.
- Narrator: The big frame brings new surrounds only. Your vents and the cup holder move across from the old panels, and so does your hazard switch.
- Narrator: If you're not sure by eye, measure it. Run a tape along your dash from the radio opening to the steering wheel trim, then lay the tape along the big frame on your towel. If the big frame is longer than that space, the small frame is yours.
- Narrator: If the big frame stops short of your steering wheel, or you'd have to cut your dash to make it fit, stop right there. Cut plastic leaves edges that never look right again. Put the small frame in instead: it sits in the radio opening, and it looks factory.
- Narrator: With the small frame it's simpler. It goes straight into the original radio opening, and your own upper panel goes back on around it later.
- Narrator: Your own hazard switch moves from the old strip into the big frame. Unplug it first, then fit it into the frame's cut-out so it sits firm and flush.
- Narrator: Are you fitting the small frame? Then your screen moves across first. Undo the screws that hold it in the big frame, lift it out, and fit it into the small frame with the same screws, turning each one until it stops and then just a touch more.
- Narrator: Keep them snug, not tight. If you over-tighten them, the metal screw cuts into the plastic frame, the frame bends, and then it won't sit flush again. Hand tight with a screwdriver is plenty.
- Narrator: Now it's time for the plugs. Your Brummstadt harness has a partner for each of your car's main radio plugs. Click each car plug into its partner: every one has its own shape, like a kids' shape puzzle.
- Narrator: Push until it clicks, then give the plug body a gentle tug. A half-latched plug drops out on the first bumpy road and takes the sound or the screen with it. And if a plug won't go in, check its shape, and never force it or cut it.
- Viewer: I've got plugs left over. Did I miss something?
- Narrator: That's normal on a HiAce. Some plugs simply stay free. The square plug with the loose wires isn't used, and neither are the round sockets for aux in, audio out and the subwoofer, or the pink AMP-C wire. It's fine to have leftover plugs.
- Narrator: On the car side, the factory plugs for GPS, Bluetooth or the old microphone have no partner either, because your Brummstadt unit has its own. Tape them up and tuck them away.
- Narrator: Has your HiAce had an aftermarket radio before? Then there may be an old adapter harness between the car and the plugs. Take it out, so your new harness plugs straight into the car's own plugs. If it stays in, the plugs won't match.
- Narrator: Your car's aerial plug goes into the black aerial plug on your harness, and that lead goes into the radio socket on the back of the unit.
- Narrator: Your box also holds a small aerial booster. Next to the yellow power wire on your harness you'll find a wire labelled ANT, often blue. Join it to the blue lead of the booster with the joiner, and your stations come in strong.
- Narrator: Leave that blue wire unconnected, and the radio may still play, but stations crackle or drop out. Connect it, and the reception comes back.
- Narrator: Two little things are easy to miss. If there's a fan plug in that bundle of round plugs, it goes into its partner, so the unit stays cool. And the other loose blue wire, the one with the rubber cap and no label, stays capped, because nothing on your HiAce needs it.
- Narrator: Your GPS aerial plugs into the socket marked GPS. Put the aerial up on top of the dash, under the plastic and away from metal, so it can see the sky.
- Narrator: Did you order the external microphone? Plug it into the small round socket marked MIC on the bundle of round plugs. Run the lead up the windscreen pillar and stick the mic on the roof lining right beside the driver's sun visor, away from the vents, so callers hear you and not the road. Tap here for our full microphone film.
- Narrator: Does your unit have a SIM holder? Fit your SIM now while everything's in your hands, and the unit gets mobile data without your phone.
- Narrator: Did you pick DAB plus? The DAB module runs from a USB lead on the unit, and its strip aerial goes on the windscreen. Tap here for more on DAB.
- Narrator: Did you pick the dash camera? It connects by USB, and you watch and control its footage right on the screen. And if you picked tyre pressure sensors, they talk to the unit through their own small USB receiver. Tap here for our tyre pressure film.
- Narrator: The OBD2 tool from your box plugs into the diagnostic port under the dashboard. It talks to the unit or your phone over Bluetooth, and it shows live engine data and fault codes.
- Narrator: Then cable-tie the long leads together and to the car's own wiring. Loose leads rattle behind the dash, and in time an edge can rub through the insulation and cause a short. A few ties keep it quiet and safe.
- Narrator: On the two hundred series HiAce there's no extra box for the steering wheel buttons. Your Brummstadt unit learns them instead, and it takes about a minute.
- Narrator: Not every two hundred series has steering wheel buttons. If yours doesn't, you control the volume on the screen instead: swipe up from the bottom edge, and the volume keys appear.
- Narrator: You'll do it right after the first power-up. Open the learning app on the unit. Then press one button on your wheel, and tap the matching symbol on the screen. Do that for every button.
- Viewer: And what if a button does nothing afterwards?
- Narrator: Then simply run the learning again for that button: press it on your wheel, then tap its symbol.
- Narrator: Now let's fit the reverse camera. Here are the key steps for your HiAce, and our full camera film has every setting and check. Tap here for it.
- Viewer: My van's a long one. Will the camera cable reach?
- Narrator: Measure it first. The camera cable in your kit is three metres long, and in a long HiAce the route from the back door to the dash can be much longer: one owner's route came to nearly nine metres. Run a string the way the cable will go, and if it's short, the ten metre extension cable sorts it.
- Narrator: Mount the Brummstadt camera on the back of the van, above the number plate. Run its lead inside along the roof lining or under the floor trim, through a rubber grommet, never over a sharp edge. Your rear parking sensors keep beeping just as before.
- Narrator: Camera power comes from the reverse light. The trigger wire, usually brown and marked BACK or REVERSE, goes to the reverse light's positive wire, and the black one goes to bare metal. With a meter, you want twelve volts in reverse and nothing in park.
- Narrator: Put the trigger on the indicator wire, and the camera jumps on every time you indicate. Check with the meter first, and the camera only comes up in reverse.
- Narrator: At the dash, the camera's yellow video plug goes into the yellow camera socket on the harness. It doesn't go into the aux sockets, or into video in.
- Narrator: Plug it into AUX, and the screen stays empty in reverse, even though everything else is right. Plug it into the camera socket instead, and the picture comes straight up.
- Narrator: If your reverse camera shows in the rear-view mirror, it stays there and keeps working. Your Brummstadt camera shows on the big screen.
- Narrator: Did your factory camera show on the old touchscreen? It can work on your new screen if it runs on twelve volts and you pick its format, usually DSV. The yellow camera adapter joins your car's camera plug to the yellow camera socket on the harness, but not every kit has one. Some Toyota cameras run on about six volts, and then a twelve to six volt step-down module in its power lead, or the Brummstadt camera, is the way.
- Narrator: Did you order the front camera as well? It has its own input on the unit, and it comes on by itself when you drive forward. Its lead runs from the grille to the dash, so measure that route too. Our camera film shows its socket and the setting for two cameras.
- Narrator: Now it's time to wake it up. Reconnect the negative terminal, snug the nut, and turn the ignition on. You'll see the Brummstadt logo, and then the home screen.
- Narrator: If the screen stays black, take the battery off again and check that the main plug has really clicked. A plug that's nearly in is the first thing to check.
- Narrator: If you ever notice a hot plug or a burning smell, switch the ignition off and disconnect the battery straight away, and check that plug before you power up again.
- Narrator: Now teach the steering wheel buttons in the learning app: press a button on your wheel, then tap its symbol, one button after the other.
- Narrator: For the radio, set the radio region to Australia. If stations are weak, raise the FM sensitivity in the factory radio settings, one step at a time.
- Narrator: Now let's set up the camera. Shift into reverse with your foot on the brake. No signal is a good sign: the screen has seen reverse. Now hold your finger on the picture until a box pops up, pick AHD ten eighty P, twenty five hertz for the Brummstadt camera, and save.
- Narrator: If you fitted the external mic, pick External Mic in the settings and set the mic gain to seven, just as our microphone film shows step by step.
- Narrator: For your phone, open Zed-Link, the app for CarPlay and Android Auto. Pair over Bluetooth for wireless, or plug in a data cable. Tap here for our phone film.
- Narrator: When it all works, take a photo of each settings screen, so you can set it back quickly after an update.
- Viewer: It works! Can I put the panel back now?
- Narrator: You nearly can, but not quite yet. Let's do ten minutes of testing first, because a fix takes seconds while the dash is open, and an evening once it's closed.
- Narrator: Touch the screen everywhere, play a song you know and change the volume, and try a radio station you know.
- Narrator: Press every steering wheel button. Make a real call, both ways, so you hear the microphone. Then connect your phone and start CarPlay or Android Auto.
- Narrator: With your foot on the brake, select reverse, and the camera comes up. Out of reverse, your normal screen is back. Then try the indicators, left and right, and the screen should stay put.
- Narrator: Switch the headlights on and check that the screen is still easy to read. Then try the hazards: they flash just like before.
- Narrator: Turn the ignition off and on again, and your settings should still be there. If something isn't right, go back to its plug or its setting. It's nearly always one of those two.
- Narrator: Is it all working? That's lovely. Switch the ignition off, and take the battery off again, so nothing's live while the leads move.
- Narrator: Feed the harness in behind the unit, every lead clear of edges and screw holes, and slide the screen and frame home.
- Narrator: If the frame won't sit flat, something's caught behind it. Don't pull it down with the screws, because they'd crush a lead and bend the frame. Lift it, free the lead, and it sits flat on its own.
- Narrator: Fix it with its screws, each one from its spot on your paper, snug and gentle.
- Narrator: Now the long upper panel goes back. Lower it into place, line up the clips along the back edge first, then press along the lower edge with the flat of your hand until each clip clicks home.
- Narrator: Put the battery back on for one last round. Listen to the sound, press the buttons, and check the camera and the hazards, because closing up can nudge a plug.
- Narrator: The battery was off, so set the clock if it needs it. It only takes a minute, and then you're done.
- Narrator: That's it. You've fitted a Brummstadt screen to your HiAce yourself. The kettle's gone cold, but you've earned a fresh cup.
- Narrator: Let's look back. You found your option, took out the factory head unit, and fitted the frame. You did the wiring and plugs, taught the steering wheel buttons, and added the camera. Then you powered up, tested, and closed it up.
- Narrator: Here's an extra tip: keep your settings photos in the glovebox. If anything ever needs a tweak, you've got everything in one place.
- Narrator: Everything in this film we learned from our own installs, our installers and lots of HiAce owners. Every one of their stories made it better.
- Narrator: Do you still have a question, or an idea for your HiAce? Ask your installer, or better still, have a yarn with us at Brummstadt. We work with these units every day, and even good installers sometimes haven't met these settings yet, which is no fault of theirs.
- Narrator: We want every HiAce owner to get it right the first time, which is why our films go this deep.
- Narrator: Now, can I ask a small favour? Before you bought, you probably read a few reviews, and somebody's five stars helped you decide.
- Narrator: If you're still deciding, good on you, you'll love it. And if you've just fitted it yourself, and this film saved you a support message and an afternoon, you're probably thinking we've earned our five stars.
- Narrator: It's one click on the review button right here, quicker than talking one stubborn clip back into its hole, and it tells the next HiAce owner they're in good hands. Enjoy the drive.
If you have still got a question about your HiAce, ask us at Brummstadt. We sell these kits and work with them every day.