Premium by Brummstadt.com.au

Expert support for Aussie drivers | 7 days a week incl. holidays

3-year head unit warranty | 30-day returns for store credit

Guaranteed fit or we'll fix it

Mic setup on your Brummstadt unit

Video, 8:30. Four steps, each one also written out below.

In this video

  1. Intro
  2. Fit the mic
  3. Mic settings
  4. Test call
  5. Still not clear?
Speed

The little external mic sits up near your head, so your voice gets there first, not the fan or the road.

Time
About ten minutes.
Have ready
Your phone, paired with the unit by Bluetooth, for a test call at the end, and the little external mic.
Screens can look different
Screens look a bit different from unit to unit, depending on the software and the theme, so go by the names.
How to watch
Watch the video once, then start again and follow along.

Step by step

The same steps as the video. Each one plays from its own spot.

Fit the mic

Play from 1:01

Do the fitting with the ignition off.

Where should the mic go?

  1. Best spot: the top of the driver's pillar, or the roof lining right beside the visor. Not on the visor itself, it flips down.
  2. Point the opening at your mouth, keep the foam on, and keep it off air vents and speakers.
  3. If the pillar trim says SRS or airbag, nothing goes on that trim: no clip, no tape, no cable, and don't prise it off. Use the roof lining beside the visor instead.
  4. Hold the mic with the clip that came with it, or a small tie, so it can't dangle or rattle. Lay the lead along the route first, to check it reaches.
  5. Run the cable under the dash, up behind the rubber door seal, and tuck it in along the front edge of the roof lining. Tie it to the car's own wiring, never to anything airbag, leave a little slack, and keep it well away from the pedals and the steering column.
  6. Behind the unit, the plug goes into the lead marked MIC, not the AUX lead, and it pushes in until it seats.

How do I know the mic is plugged in properly?

Play from 2:53

An easy test, and you don't need to pull the unit out. Best done before the dash trim goes back on.

  1. Park up and turn the key to accessory so the screen is on. These menus are for when you are stopped.
  2. Open a voice recorder app (not the dash cam one) and start recording. Tap the little mic, then tap the hole in the glass, and play it back.
  3. If the little mic sounds loud and clear, it is plugged in and working.
  4. No recorder app on your unit? Ring a friend over Bluetooth, hold the little mic to your mouth, then speak toward the hole in the glass, and ask which one sounds clearer.

Mic settings

Play from 3:33

Mic gain is how loud you sound to the person you are calling.

  1. Open your apps and tap CarSetting, then System Settings, bottom right.
  2. This list also has Factory Reset. That one wipes your apps and settings, so leave it alone. Tap Factory Setting, the last one in the list, then the Factory Setting button.
  3. Enter the code 16176699 and tap Confirm. All eight digits open the whole menu, mic settings included.
  4. On the left, swipe up until you see Customized Setting and tap it. Gain Setting is your music and radio volume, not the mic.
  5. On the right, swipe up until you see mic gain. Take a photo of the page first, so you can always put it back.
  6. Tap mic gain and set it to 7. On most units, 7 is the highest. If your unit also has a bt mic gain row, set that to 7 too. Leave everything else on this page as it is.
  7. Keep swiping up on the right, nearly to the bottom, and look for External Mic. Only tick it once the mic is plugged in. If the box is empty, give it a tick. No External Mic row? Then your unit doesn't need it, mic gain does the job.
  8. Tap Save, the last word at the top right, just once. The unit saves and restarts by itself: you see the Brummstadt logo, then your home screen. Give your phone a moment to connect again.

Test call

Play from 6:07
  1. Ring someone over Bluetooth from the unit, and just talk normally from your seat.
  2. If you mostly call through CarPlay or Android Auto, test that too. If only that call sounds poor, check on your phone's call screen that the audio is going through the car.
  3. If they hear you less clearly, or not at all, put the mic settings back from your photo, untick External Mic if you ticked it, tap Save, and test again.

Still not clear?

Play from 7:03
  1. The plug: pushed right in. If you need to, ease the unit forward with the ignition off, then do the tap test.
  2. The spot: opening at your mouth, off the vents, close to you.
  3. Noise: fine when you are parked but bad on the road? That is usually wind, the fan or the vents, not a faulty mic. Windows up, fan down a notch.
  4. Callers hear hiss, or say you are too loud? Try mic gain one step lower. An echo? Turn the call volume down a little.
  5. Still muffled after all that? Hold the mic right at your mouth for a test call. Clear means it just needs a better spot. Still bad? Plug it into a laptop or a phone with a mic socket. If it is quiet there too, the mic is faulty and needs replacing.

Questions from customers

Real questions Brummstadt owners asked us, with the answer.

People can barely hear me when I call.

Fit the little external mic up near your head, so your voice gets there first, not the fan or the road. Then set mic gain to 7 (it lives in Factory Setting, under Customized Setting) and make a test call.

See it in the video at 0:00

Can I use the factory mic, or do I need the external one?

The car's own roof mic usually isn't connected to your Brummstadt unit, so use the little external mic. It sits up near your head, so your voice gets there first.

See it in the video at 1:01

Where is the best place to put the mic?

Best spot: the top of the driver's pillar, or the roof lining right beside the visor, not on the visor itself, it flips down. Point the opening at your mouth and keep it off air vents and speakers. If the pillar trim says SRS or airbag, use the roof lining beside the visor instead.

See it in the video at 1:01

Where does the mic plug in?

Behind the unit, the plug goes into the lead marked MIC, not the AUX lead, and it pushes in until it seats. To check it, record with a voice recorder app, tap the little mic, then tap the hole in the glass: if the little mic sounds loud and clear, it is plugged in and working.

See it in the video at 1:01

The mic doesn't seem to work when I call through Android Auto or CarPlay.

Test that call too, not just a Bluetooth call. If only the CarPlay or Android Auto call sounds poor, check on your phone's call screen that the audio is going through the car.

See it in the video at 6:07

When I'm stopped it sounds fine, but when I drive people can hardly hear me over the noise.

Fine when you are parked but bad on the road? That is usually wind, the fan or the vents, not a faulty mic. Windows up, fan down a notch, and keep the mic opening at your mouth, off the vents and close to you.

See it in the video at 7:03

The people I call can hear an echo of their own voice.

An echo? Turn the call volume down a little. If callers hear hiss, or say you are too loud, try mic gain one step lower.

See it in the video at 7:03

Did this video help?

Ask a question about this video

Your question comes straight to the Brummstadt team and is not shown on this page. We answer by email, and the questions we get help us make this video and its steps even better.

0 of 1500 characters

Brummstadt uses your name and email only to answer this question. Without an email we cannot reply. Nothing you write here is published. Privacy policy

Brummstadt sells these units and works with them every day. A mic that seems broken often only needs the right setting.

The mic in this video

External hands-free microphone

External hands-free microphone

The little external mic that sits up near your head for clear calls.

See the external mic

More setup videos

Installation videos

Fitting it to a Ranger? Watch the installation video.

Full transcript
  1. Liam: Right, Jess. Let's make sure people hear you loud and clear when you call from your Brummstadt unit.
  2. Jess: Go on then, show me.
  3. Liam: If anyone's ever said you sound far away or muffled on a call, this is where we start.
  4. Liam: Here's what's coming. One, fit the little mic in the right spot and check it works. Two, the mic settings on your Brummstadt unit. Three, a test call. And four, what to check if it's still not clear.
  5. Jess: So by the end, people hear me properly?
  6. Liam: That's the idea. Have your phone and the little mic handy, and allow about ten minutes. Two names you'll hear: Factory Setting, the menu where the mic settings live, and mic gain, how loud you sound to the other person.
  7. Liam: Best way to use this video? Watch it once all the way through, hands off, so you get the whole idea. Then start again and do it with us, step by step. Pause whenever you need.
  8. Jess: So watch first, then follow along. Got it.
  9. Liam: First, the mic itself. Your Brummstadt unit has a tiny built-in mic, that little hole in the glass. But it sits low in the dash, close to the fan and the vents, a long way from your mouth.
  10. Jess: So that's why I sound far away?
  11. Liam: Exactly. The little external mic sits up near your head, so your voice gets there first, not the fan or the road.
  12. Jess: So it's this one up here, not the one in the roof?
  13. Liam: That's the one. The car's own roof mic usually isn't connected to your Brummstadt unit. The best spot is the top of the driver's pillar, or the roof lining right beside the visor. Not on the visor itself, it flips down.
  14. Liam: Point the opening at your mouth, keep the foam on, and keep it off air vents and speakers. If the pillar says SRS or airbag, nothing goes on that trim. No clip, no tape, no cable, and don't prise it off.
  15. Liam: Use the clip that came with it, or a small tie, so it can't dangle or rattle. Lay the lead along the route first, to check it reaches.
  16. Liam: The cable runs under the dash, up behind the rubber door seal, and tucks in along the front edge of the roof lining. Keep it clear of any trim marked SRS or airbag.
  17. Liam: Tie it to the car's own wiring, never to anything airbag, and leave a little slack. Keep it well away from the pedals and the steering column.
  18. Liam: Behind the unit, the plug goes into the lead marked MIC, not the AUX lead, and it pushes in until it seats.
  19. Liam: Park up, and turn the key to accessory so the screen's on. These menus are for when you're stopped.
  20. Jess: How do I know it's in properly?
  21. Liam: Easy test, and you don't need to pull the unit out. Open a voice recorder app, not the dash cam one, start recording, tap the little mic, then tap the hole in the glass, and play it back.
  22. Liam: If the little mic sounds loud and clear, it's plugged in and working. Best done before the dash trim goes back on.
  23. Liam: No recorder app on your unit? Ring a mate over Bluetooth, hold the little mic to your mouth, then speak toward the hole in the glass, and ask which one sounds clearer.
  24. Liam: And have your phone paired with the unit by Bluetooth, for a quick test call at the end.
  25. Liam: Screens look a bit different from unit to unit, depending on the software and the theme. So just go by the names.
  26. Liam: Open your apps and tap CarSetting.
  27. Liam: Then System Settings, bottom right.
  28. Liam: This list also has Factory Reset. That one wipes your apps and settings, so we leave it alone.
  29. Jess: Not that one.
  30. Liam: We want Factory Setting, the last one in the list. Setting, not Reset. Tap it, then the Factory Setting button.
  31. Liam: It asks for a code. One, six, one, seven, six, six, nine, nine.
  32. Jess: I saw a shorter one online. One six one seven?
  33. Liam: Stick with all eight digits. They open the whole menu, mic settings included. Tap Confirm.
  34. Liam: On the left, swipe up until you see Customized Setting. We're only touching the mic in here.
  35. Jess: What about Gain Setting?
  36. Liam: That's your music and radio volume. The mic lives in Customized Setting, so tap that.
  37. Liam: Now swipe up on the right until you see mic gain. That's how loud you sound to the person you're calling.
  38. Jess: It's on four. Should I take a photo first?
  39. Liam: Good thinking. Then you can always put it back.
  40. Liam: Tap mic gain and set it to seven. On most units, seven's the highest.
  41. Jess: Seven.
  42. Liam: Some units also have a bt mic gain row. If yours does, set that to seven too. Leave everything else on this page as it is.
  43. Liam: Now keep swiping up on the right, nearly to the bottom, and look for External Mic. Only tick it once the mic is plugged in. If the box is empty, give it a tick.
  44. Jess: And if it isn't there?
  45. Liam: Then your unit doesn't need it. Mic gain does the job. We'll save and test the call.
  46. Liam: Now tap Save, the last word at the top right, just once. The unit saves and restarts by itself.
  47. Jess: There it goes.
  48. Liam: That's normal. You'll see the Brummstadt logo, then your home screen. Give your phone a moment to connect again.
  49. Liam: Now a test call. Ring someone over Bluetooth from the unit, and just talk normally from your seat.
  50. Jess: Let's try Mum.
  51. Mum: Hello, love!
  52. Jess: Hi Mum, I'm in the ute, testing the mic. How do I sound?
  53. Mum: Lovely and clear, love. Every word.
  54. Jess: Perfect. I'll ring you tonight, Mum. Bye!
  55. Mum: Righto. Bye, love.
  56. Liam: If you mostly call through CarPlay or Android Auto, test that too. If only that call sounds poor, check on your phone's call screen that the audio is going through the car.
  57. Liam: And if they hear you less clearly, or not at all, put the mic settings back from your photo, untick External Mic if you ticked it, tap Save, and test again.
  58. Liam: Still not as clear as it should be on your Brummstadt unit? Three quick things.
  59. Liam: One, the plug. Pushed right in. If you need to, ease the unit forward with the ignition off, then do the tap test. Two, the spot. Opening at your mouth, off the vents, close to you.
  60. Liam: Three, noise. Fine when you're parked but bad on the road? That's usually wind, the fan or the vents, not a faulty mic. Windows up, fan down a notch.
  61. Liam: Callers hear hiss, or say you're too loud? Try mic gain one step lower. An echo? Turn the call volume down a little.
  62. Jess: And if it's still muffled after all that?
  63. Liam: Hold the mic right at your mouth for a test call. Clear means it just needs a better spot. Still bad? Plug it into a laptop or a phone with a mic socket. If it's quiet there too, the mic is faulty and needs replacing.
  64. Narrator: If you've still got a question, ask your installer, or best of all, ask us at Brummstadt. We sell these units and work with them every day. Even good installers sometimes think a mic or a camera is broken, when it only needs the right setting. That's product know-how, and it's what we're here for.
  65. Narrator: And if you've got an idea, or something new in mind for your car, we'd love to hear it at Brummstadt.

If you have still got a question, ask your installer, or best of all, ask us at Brummstadt. We sell these units and work with them every day, and a mic that seems broken often only needs the right setting.