Premium by Brummstadt.com.au

Expert support for Aussie drivers | 7 days a week incl. holidays

3-year head unit warranty | 30-day returns for store credit

Guaranteed fit or we'll fix it

Rear camera extension cable for your Brummstadt head unit

Video, 1:32. Three steps, each one also written out below.

The 10 metre cable goes in between your camera cable and your head unit and gives the camera the reach it needs.

What it is for
A reverse camera on a tray, a canopy, a caravan or a trailer.
On the cable
Yellow RCA plugs carry the picture. Beside them runs a separate red wire with bare ends, for a reverse signal or accessory power.
How to watch
Watch the video once, then start again and follow along.

Step by step

The same steps as the video. Each one plays from its own spot.

What's on the cable

Play from 0:11
  1. The yellow RCA plugs carry the picture between a compatible camera and your head unit.
  2. Beside them runs a separate red wire with bare ends, for a reverse signal or accessory power.

Connecting it

Play from 0:24
  1. It goes in between your camera cable and your head unit's camera input.
  2. Push each yellow plug fully home and give it a gentle tug. A plug that's only half in can leave you without a picture.
  3. Join the red wire to a suitable circuit, for example the reverse signal, so your screen switches to the camera in reverse.
  4. Its ends are bare, so you can crimp them, tap into the existing wiring, or have it fitted professionally.

Routing tips

Play from 0:53
  1. Lay the cable along the route first, so you know where every metre goes.
  2. Run it along the existing wiring and hold it with cable ties, so nothing rattles or rubs through.
  3. Keep it clear of the exhaust and sharp edges, and pass it through rubber boots or grommets, so it can't get pinched.
  4. Leave a little slack at each end, so the plugs never pull tight.
  5. Then select reverse, and the view from the back is right there on your screen.

Questions from customers

Real questions Brummstadt owners asked us, with the answer.

Do I need the extension cable?

If your reverse camera is going on a tray, a canopy, a caravan or a trailer, the 10 metre cable gives it the reach to your head unit.

See it in the video at 0:00

What is the red wire for?

It is a separate wire with bare ends, for a reverse signal or accessory power. Joined to the reverse signal, it makes your screen switch to the camera in reverse.

See it in the video at 0:11

Where does the extension cable plug in?

It simply goes in between your camera cable and your head unit's camera input.

See it in the video at 0:24

How do I stop the cable rattling or getting pinched?

Run it along the existing wiring and hold it with cable ties. Keep it clear of the exhaust and sharp edges, pass it through rubber boots or grommets, and leave a little slack at each end so the plugs never pull tight.

See it in the video at 0:53

There is no picture after connecting the cable.

Check that each yellow plug is pushed fully home and give it a gentle tug. A plug that's only half in can leave you without a picture.

See it in the video at 0:24

Did this video help?

Ask a question about this video

Your question comes straight to the Brummstadt team and is not shown on this page. We answer by email, and the questions we get help us make this video and its steps even better.

0 of 1500 characters

Brummstadt uses your name and email only to answer this question. Without an email we cannot reply. Nothing you write here is published. Privacy policy

If you have got a question about your setup, the Brummstadt team is always happy to help.

The cable in this video

Extension cable for the rear camera, 10 m

Ten metres of extra reach for a camera on a tray, canopy, caravan or trailer.

See the extension cable

More setup videos

Full transcript
  1. Narrator: Is your reverse camera going on a tray, a canopy, a caravan or a trailer?
  2. Narrator: Then this 10 metre extension cable from Brummstadt gives it the reach it needs.
  3. Narrator: The yellow RCA plugs carry the picture between
  4. Narrator: a compatible camera and your head unit.
  5. Narrator: Beside it runs a separate red wire with bare ends,
  6. Narrator: for a reverse signal or accessory power.
  7. Narrator: It simply goes in between your camera cable and your head unit's camera input.
  8. Narrator: Push each yellow plug fully home and give it a gentle tug,
  9. Narrator: because a plug that's only half in can leave you without a picture.
  10. Narrator: Join the red wire to a suitable circuit, for example the reverse
  11. Narrator: signal, so your screen switches to the camera in reverse.
  12. Narrator: Its ends are bare, so you can crimp them, tap
  13. Narrator: into the existing wiring, or have it fitted professionally.
  14. Narrator: Lay the cable along the route first, so you know where every metre goes.
  15. Narrator: Run it along the existing wiring and hold
  16. Narrator: it with cable ties, so nothing rattles or rubs through.
  17. Narrator: Keep it clear of the exhaust and sharp edges, and pass
  18. Narrator: it through rubber boots or grommets, so it can't get pinched.
  19. Narrator: Leave a little slack at each end, so the plugs never pull tight.
  20. Narrator: Then select reverse, and the view from the back is right there on your screen.
  21. Narrator: If you've got a question about your setup,
  22. Narrator: the Brummstadt team is always happy to help.

If you have got a question about your setup, ask us at Brummstadt. We sell these units and work with them every day.