Fit your Brummstadt screen to a Toyota HiAce H300 (2019 to 2024)
Fit the Brummstadt screen to your HiAce yourself, one step at a time, and test everything while the dash is still open.
- Time
- About 25 minutes to watch. First time, give yourself one to three hours to fit it; done it before, it's often done in under an hour.
- Have ready
- Plastic trim tools, a Phillips screwdriver, a spanner for the battery clamp, a few cable ties, and a multimeter if you're fitting a camera.
- Two dash layouts
- The HiAce has two dash layouts, and what sits under your climate knobs decides which one is yours. The screen size and the frame follow your layout.
- How to watch
- Watch it once to the end first, because the end holds a few extra tips. Then start again and follow along, pausing whenever you like.
Does this video fit your car?
One video for both dash layouts of the HiAce 300 Series. Check these points before you start.
- Your van
- This video is for the HiAce 300 Series that arrived in 2019. Whether you drive the long van, the crew van, the super long van or the Commuter, the shape under your climate knobs is what decides your kit.
- Years
- The video shows the HiAce 300 Series from 2019 to 2024. Factory screens differ by year, so yours may look a little different from the one shown. Go by the shape of the black centre panel.
- Your dash layout
- Is there a second panel below your three climate knobs and the row of small switches, with two more knobs marked rear, cooler and heater? Then yours is the Dashboard with rear climate controls. Is that area open instead, with a small tray under the switches and space below it? Then yours is the Dashboard with open lower center area. The little word rear on your left knob is the rear demister switch, and it's on both dashes.
- Screen size
- The screen size follows your layout. With rear climate controls it's the 9 inch, and with the open lower center area it's the 10.1 inch. Each one comes in its own frame, made for that dash, and a frame held against the other dash won't fit around your knobs.
- 13.3 inch screen
- The 13.3 inch fits both layouts. It's a big screen that sits out in front of the dash, rather than flush in it, and on some dashes it covers part of the air vents or the hazard switch. Hold it up to your dash and have a good look from the driver's seat before you start.
- What stays
- Your climate knobs stay and look out through the new frame, your hazard switch stays put, and your parking sensors keep working on their own. Nothing in the dash gets cut.
- Steering wheel buttons
- The small CAN box in your kit passes on your steering wheel buttons and some car information, like an open door. Your HiAce isn't in the unit's car list by name, so you pick a Toyota entry and press every button on your wheel until they all work.
- Factory camera
- Every 300 Series HiAce came with a reversing camera. It can keep working on your new screen if it runs on 12 volts, and the guide lines then come from your Brummstadt unit. If it reads about 6 volts, a 12 to 6 volt step-down module in its power lead, or the Brummstadt camera, is the way.
- Navigation arrows
- If your HiAce shows navigation arrows between the dials, those came from the factory navigation, so they won't show there any more. Your maps run on the big screen instead.
- Toyota Granvia
- Do you drive a Toyota Granvia from 2019? Then this kit and this video are made for it too.
- Not in this video
- A Japanese import that still has the older shape, with the flat nose and the older dash, takes our kit for the older HiAce, even if it was built after 2019. The dash of the 2025 update, with its new centre console, is not shown in this video. If your dash looks different from both layouts, compare it with the pictures in the video, shape by shape, before you take anything apart.
What you need
- Tools
- Plastic trim tools
- A Phillips screwdriver
- A spanner for the battery clamp
- A few cable ties
- For a camera: a multimeter
- Time
- First time, give yourself one to three hours. Done this before? Then it's often done in under an hour.
- In the box
- Your Brummstadt screen with the frame for your layout
- The plug-in harness, the same for both layouts
- A small CAN box for your steering wheel buttons, with its short data lead
- The GPS aerial
- Any camera, microphone or other extras you picked
- Good to have
- A towel to lay every part out on, so anything missing shows up now, and another on the passenger seat for the parts you take off.
Optional parts
Each one has its own page, and you can also add it on the kit page when you order.
- Trim removal toolsFour plastic pieces that take the trim off without scratches.
- Rear cameraAHD 1080p reverse camera with night vision. It comes on when you select reverse.
- Front cameraAHD 1080p forward view camera with night vision. With a rear camera as well, you switch on Double recording, so both cameras work.
- Rear camera extension cableA 10 m extension: the camera cable in the kit is 3 m, and a long HiAce is more than 5 m from end to end.
- External microphoneA hands-free mic on a 3 m lead, beside the driver's sun visor, so callers hear you and not the road.
- DAB+ digital radio adapterDigital radio from a USB lead on the unit, with a strip aerial on the windscreen.
- Tyre pressure sensors (TPMS)Kits with 4 or 8 sensors, external or internal, talking to the unit through their own small USB receiver. Internal sensors are fitted at a tyre shop.
- OBD2 diagnostic toolA Bluetooth reader for the diagnostic port: live engine data and fault codes.
Step by step
The same steps as the video. Each one plays from its own spot.
Which option is yours
Play from 1:13- On our product page, your HiAce asks for its factory dashboard layout, and there are two. One is called Dashboard with rear climate controls, and the other is Dashboard with open lower center area.
- Look just below your three climate knobs and the row of small switches. Is there a second panel there with two more knobs, marked rear, cooler and heater? Then yours is the Dashboard with rear climate controls.
- Don't let the little word rear on your left knob fool you. That's the switch for the rear demister, and it's on both dashes. What decides it is what sits under your knobs.
- Is that area open instead, with a small tray under the switches and space below it? Then yours is the Dashboard with open lower center area.
- Take a photo of your own dash and hold it next to the two pictures in the video. Whether you drive the long van, the crew van, the super long van or the Commuter, the shape under your knobs is what decides it.
- The screen size follows your layout. With rear climate controls it's the 9 inch, and with the open lower center area it's the 10.1 inch. Each one comes in its own frame, made for that dash.
- The two frames look alike at first glance, so check your layout before you start. The 9 inch frame is shaped around the rear climate controls, and the 10.1 inch frame is shaped for the open area. Hold a frame against the other dash, and it won't fit around your knobs.
- Did you pick the 13.3 inch? It fits both layouts. It's a big screen that sits out in front of the dash, rather than flush in it.
- On some dashes it covers part of the air vents or the hazard switch. So hold the screen up to your dash and have a good look from the driver's seat before you start.
- Here's what's in your box: your Brummstadt screen with the frame for your layout, and the plug-in harness. There's also a small CAN box for your steering wheel buttons. The harness is the same for both layouts, and only the screen and the frame change.
- Any camera, microphone or other extras you picked come in the same box, and each one gets its own step.
- The memory and storage version you picked doesn't change a single step.
- At the end, there's a big bright screen in a black frame that matches your dash, with your own climate knobs right below it, and a harness that plugs into your car's own plugs. Nothing in the dash gets cut.
- One thing changes. If your HiAce shows navigation arrows between the dials, those came from the factory navigation, so they won't show there any more. Your maps run on the big screen instead.
- Is your HiAce a Japanese import that still has the older shape, with the flat nose and the older dash, even if it was built after 2019? Then it takes our kit for the older HiAce.
- Do you drive a Toyota Granvia from 2019? Then this kit and this video are made for it too.
- If your dash looks different from both pictures, put your photo next to them before you take anything apart, and compare them shape by shape.
Before you start
Play from 5:03- Our one rule for the whole install is feel, not force. If something won't move, there's a reason.
- Lay every part out on a towel first, so anything missing shows up now and not halfway through. Put another towel on the passenger seat for the parts you'll take off.
- You'll need plastic trim tools and a Phillips screwdriver. Add a spanner for the battery clamp and a few cable ties. If you're fitting a camera, a multimeter makes it easy, and if you ticked the trim removal tools, they're already in your box.
- Why plastic tools? Because a metal screwdriver leaves marks in the soft trim for good. A plastic tool slides in, and the panel comes away clean.
- Take a photo of your dash now, and later another of the back of the old head unit before you unplug anything. Those photos let you compare every plug in a moment.
- Last, try the old system once. Play the radio, press the buttons on your steering wheel and look at the reverse camera. Then listen to the parking sensors and flash the hazards, so you know what normal looks like.
- Next is the battery. Switch the ignition and the lights off, then undo the negative terminal, the one marked minus, and tuck the lead aside in a cloth.
- With the battery connected, a bare pin touching metal can blow a fuse, and then the screen stays dark on the day. A minute with a spanner saves you an afternoon.
Remove the factory head unit
Play from 6:54- Here's how your HiAce dash is built. The factory screen and your three climate knobs sit together in one black centre panel. The light surround around it stays in the car, and so does your hazard switch, up at the top by the driver's vent.
- Factory screens differ by year, so yours may look a little different from the one shown here. Go by the shape of the black panel, and take it slowly.
- On an automatic, the gear selector sits right beside the panel, so work carefully around it. On a manual, the gear stick comes up from the floor and stays out of the way.
- Start at the bottom edge of the black panel. Slide a plastic tool into the gap, and ease the panel out until the first clips let go.
- Then work up both sides, one clip at a time, with the tool right next to each clip.
- Lever in one spot, or yank the whole panel at once, and a clip snaps or the plastic cracks, and then that panel rattles for good. Go clip by clip, and each one lets go with a small pop.
- If there's a narrow strip along the top of the screen that lifts away on its own, ease it off first. Then the whole panel, with the screen and the knobs, comes towards you.
- It's still connected behind, so stop as soon as you see wires. Pull it further, and a lead can come out of its plug.
- Reach behind and unplug your climate knobs. Press the tab first, then pull the plug body, never the wires.
- The hazard switch doesn't come out with it. It sits in the light surround above the driver's vent, and it stays right there, plugged in and working.
- Now take out the factory head unit itself. It sits in a metal frame behind the panel, held by screws on both sides. Undo them, and tape each screw to a piece of paper, so none gets lost behind the dash.
- Slide it forward just far enough to reach the back, then unplug each plug. Press the tab first, then pull the plug body.
- Pull on the wires instead, and a thin lead can tear out of its plug, with no slack left to fix it. Press the tab, pull the body, and it slides out easily.
- The old head unit's out. Keep it boxed with its screws, in case you ever sell the HiAce.
- Your new Brummstadt frame has three round openings, and your climate knobs look out through them. Compare the back of your old panel with your new frame, and fit the climate unit the same way it was held, snug and gentle. Keep the old panel until the knobs work in the new frame.
Fit the frame
Play from 9:58- Before anything gets screwed in, hold your new frame up to the dash, with nothing plugged in yet. This trial fit takes a minute, and it tells you everything.
- With the 9 inch frame, your climate knobs look out through its three round openings, and your rear climate controls look out through the opening below them.
- With the 10.1 inch frame, the frame fits around your knobs and the open area below, and your small tray stays right where it was.
- With the 13.3 inch, sit in the driver's seat and check that the screen clears your vents and your hazard switch, before you fix anything.
- Keep the screws snug, not tight. If you over-tighten them, the metal screw cuts into the plastic frame, the frame bends, and then it won't sit flush again. Hand tight with a screwdriver is plenty.
- If the frame doesn't line up with your knobs, stop there, and check your layout against the two pictures again. Forcing a frame into place cracks the plastic, and a cracked frame never looks right again.
Wiring and plugs
Play from 11:10- Now it's time for the plugs. Your Brummstadt harness is the same for both layouts, and it has a partner for each of your car's radio plugs. Every one has its own shape, like a kids' shape puzzle.
- Before you click anything in, hold the harness plugs next to the car's plugs, and compare them with your photo. They should match, shape for shape.
- If a plug doesn't match its partner, stop, and don't force it, because a bent pin never answers again. Compare the shapes one by one, and find the partner that fits.
- Push until it clicks, then give the plug body a gentle tug. A half-latched plug drops out on the first bumpy road and takes the sound or the screen with it.
- If your box has two harnesses, and the screen stays dark with the key on, turn the ignition off, then swap to the other one.
- Plugs left over are normal. Your Brummstadt unit brings its own GPS and Bluetooth, and its own microphone too, so the car's plugs for those have no partner. Tape them up and tuck them away.
- If your HiAce has a factory amplifier, compare its plugs with your harness, shape by shape. Leave any plug without a partner unplugged, and test the sound before you close up.
- Your car's aerial plug goes into the aerial lead on your harness, and that lead goes into the round radio socket on the back of the unit.
- Your GPS aerial plugs into the socket marked GPS. Put it up on top of the dash, under the plastic and away from metal, so it can see the sky.
- Your unit's USB leads come out at the back, so run the one for your phone forward to a spot you can reach, like the tray. Use a separate charger for your phone, because these USB leads don't charge it.
- Did you order the external microphone? Plug it into the small round socket marked MIC on the bundle of round plugs. Its lead is three metres long, so run it up the windscreen pillar and stick the mic on the roof lining beside the driver's sun visor, away from the vents, so callers hear you and not the road.
- Does your unit have a SIM holder? Fit your SIM now while everything's in your hands, and the unit gets mobile data without your phone.
- Did you pick DAB+? The DAB module runs from a USB lead on the unit, and its strip aerial goes on the windscreen.
- Did you pick the dash camera? It connects by USB, and you watch its footage right on the screen. And if you picked tyre pressure sensors, they talk to the unit through their own small USB receiver.
- The OBD2 tool plugs into the diagnostic port under the dashboard. It talks to the unit or your phone over Bluetooth, and it shows live engine data and fault codes.
- Then cable-tie the long leads together and to the car's own wiring. Loose leads rattle behind the dash, and in time an edge can rub through the insulation and cause a short. A few ties keep it quiet and safe.
CAN box and steering wheel buttons
Play from 14:49- Your HiAce talks to the screen through the small CAN box in your kit. It passes on your steering wheel buttons and some car information, like an open door.
- The CAN box has a short data lead with a small plug. Push it into its socket on the back of the unit, while the battery's still off.
- If the screen works but the steering wheel buttons do nothing, look at that short data lead first. One owner's buttons did nothing until that small plug was pushed all the way home, and then every button answered.
- After the first power-up, you'll pick your car in the unit's settings. Open My Car, then Diagnosis, then Car, and pick the maker that's printed on your CAN box.
- Your HiAce isn't in that list by name, so pick a Toyota entry, and then press every button on your wheel. If one doesn't answer, go back and try the next Toyota entry, until they all work.
- Here's a quick check that the entry is right: open a door, and the screen shows a little picture of the open door.
Reverse camera
Play from 16:03- Here are the key steps for your HiAce. Our full camera video has every setting and check.
- Every 300 Series HiAce came with a reversing camera. It can keep working on your new screen if it runs on 12 volts, and the guide lines then come from your Brummstadt unit.
- So measure it before you plug it in. With the car in reverse, a meter on the camera's power wire should show 12 volts. If it reads about 6 volts, a 12 to 6 volt step-down module in its power lead, or the Brummstadt camera, is the way.
- Some HiAce models have a digital rear-view mirror with its own camera. Leave its wiring as it is, and test it in reverse before you close up.
- Long van? Measure first. The camera cable in your kit is three metres long, and a long HiAce is more than five metres from end to end, so the route from the back door to the dash is much longer. Run a string the way the cable will go, and if it's short, the ten metre extension cable sorts it.
- Mount the Brummstadt camera on the back of the van, centred above the number plate. Run its lead inside along the roof lining or under the floor trim, through a rubber grommet, never over a sharp edge. Your parking sensors keep beeping just as before.
- Camera power comes from the reverse light. Its trigger wire goes to the reverse light's positive wire, and the black one goes to bare metal. With a meter, you want 12 volts in reverse and nothing in park.
- Put the trigger on the indicator wire, and the camera jumps on every time you indicate. Check with the meter first, and the camera only comes up in reverse.
- At the dash, the camera's yellow video plug goes into the yellow camera socket on the harness. Then the picture comes up as soon as you select reverse.
- Did you order the front camera as well? Its lead plugs into the fifth white socket on the back of the unit, and you switch on Double recording in the settings, so both cameras work. Our camera video shows each step.
First power-up and settings
Play from 18:33- Reconnect the negative terminal, snug the nut, and turn the ignition on. You'll see the Brummstadt logo, and then the home screen.
- If the screen stays black, take the battery off again and check that the main plug has really clicked. A plug that's nearly in is the first thing to check.
- If you ever notice a hot plug or a burning smell, switch the ignition off and disconnect the battery straight away, and check that plug before you power up again.
- Now set your car in My Car, Diagnosis and Car, and press every steering wheel button to test it.
- If there's no sound, the CAN list is rarely the reason. Check that the main plug is clicked fully home, then check the volume, and play a song from your phone.
- For the radio, set the radio region to Australia. If stations are weak, raise the FM sensitivity in the radio settings, one step at a time.
- Now set up the camera. Shift into reverse with your foot on the brake. No signal is a good sign: the screen has seen reverse. Hold your finger on the picture until a box pops up. Pick AHD1080P-25Hz for the Brummstadt camera, or the format your factory camera needs, usually DSV, and then tap save.
- If you fitted the external mic, pick External Mic in the settings and set the mic gain to 7, just as our microphone video shows step by step.
- For your phone, open ZLINK, the app for CarPlay and Android Auto. Pair over Bluetooth for wireless, or plug in a data cable.
- When it all works, take a photo of each settings screen, so you can set it back quickly after an update.
Test before closing
Play from 20:40- Do ten minutes of testing first, because a fix takes seconds while the dash is open, and an evening once it's closed.
- Touch the screen everywhere, play a song you know and change the volume, and try a radio station you know.
- Press every steering wheel button. Make a real call, both ways, so you hear the microphone. Then connect your phone and start CarPlay or Android Auto.
- With your foot on the brake, select reverse, and the camera comes up. Out of reverse, your normal screen is back. Then try the indicators, left and right, and the screen should stay put.
- Back up slowly towards something soft, and the parking sensors should beep just as before. Then glance at the instrument cluster: there shouldn't be any new warning message.
- If a warning does come up, switch off and check that every plug you touched is fully home, then test again before you close anything.
- Switch the headlights on and check that the screen is still easy to read. Then press the hazards: they flash just like before.
- Turn the ignition off and on again, and your settings should still be there. If something isn't right, go back to its plug or its setting. It's nearly always one of those two.
Closing up and done
Play from 22:16- All working? Switch the ignition off, and take the battery off again, so nothing's live while the leads move.
- Feed the harness in behind the unit, every lead clear of edges and screw holes, and slide the screen and frame home where the black panel was.
- If the frame won't sit flat, something's caught behind it. Don't force it down, because that would crush a lead and bend the frame. Lift it, free the lead, and it sits flat on its own.
- Now fix your frame in place with the fixings from your kit, snug and gentle, never forced. If you lifted off the narrow strip along the top, press it back on now, clip by clip.
- Put the battery back on for one last round. Listen to the sound, press the buttons, and check the camera and the hazards, because closing up can nudge a plug.
- The battery was off, so set the clock if it needs it. It only takes a minute, and then you're done.
- An extra tip: keep your settings photos in the glovebox. If anything ever needs a tweak, you've got everything in one place.
Questions from customers
Questions HiAce owners asked us, answered in the video.
Which screen size do I need for my HiAce?
The screen size follows your dash layout. With rear climate controls it's the 9 inch, and with the open lower center area it's the 10.1 inch. Each one comes in its own frame, made for that dash.
The two frames look alike at first glance, so check your layout before you start. Hold a frame against the other dash, and it won't fit around your knobs.
See it in the video at 2:27Will the 13.3 inch screen fit my dash?
It fits both layouts. It's a big screen that sits out in front of the dash, rather than flush in it.
On some dashes it covers part of the air vents or the hazard switch. So hold the screen up to your dash and have a good look from the driver's seat before you start.
See it in the video at 3:01Will the navigation arrows between my dials still show?
No. Those arrows came from the factory navigation, so they won't show there any more. Your maps run on the big screen instead.
See it in the video at 4:15My HiAce is a Japanese import built after 2019. Which kit does it take?
Go by the shape. If it still has the older shape, with the flat nose and the older dash, it takes our kit for the older HiAce, even if it was built after 2019.
A Toyota Granvia from 2019 takes this kit, and this video is made for it too.
See it in the video at 4:29The screen works, but the steering wheel buttons do nothing. What now?
Look at the CAN box's short data lead first. One owner's buttons did nothing until that small plug was pushed all the way home, and then every button answered.
Your HiAce isn't in the car list by name. Open My Car, then Diagnosis, then Car, pick a Toyota entry, and press every button on your wheel. If one doesn't answer, try the next Toyota entry, until they all work.
See it in the video at 15:12Can I keep my factory reversing camera?
Every 300 Series HiAce came with a reversing camera. It can keep working on your new screen if it runs on 12 volts, and the guide lines then come from your Brummstadt unit.
So measure it before you plug it in: with the car in reverse, a meter on the camera's power wire should show 12 volts. If it reads about 6 volts, a 12 to 6 volt step-down module in its power lead, or the Brummstadt camera, is the way.
See it in the video at 16:16My van is a long one. Will the camera cable reach?
Measure it first. The camera cable in your kit is three metres long, and a long HiAce is more than five metres from end to end, so the route from the back door to the dash is much longer.
Run a string the way the cable will go, and if it's short, the ten metre extension cable sorts it.
See it in the video at 16:56The screen stays dark when I turn the key. What do I check?
Take the battery off again and check that the main plug has really clicked. A plug that's nearly in is the first thing to check.
If your box has two harnesses, and the screen stays dark with the key on, turn the ignition off, then swap to the other one.
See it in the video at 18:46After fitting
Once the screen is in and tested, these videos help you set up the rest. The installation video points to them along the way.
- Connect your phone to your Brummstadt unitZLINK for Apple CarPlay and Android Auto: pair over Bluetooth for wireless, or plug in a data cable. Video, 9:44.
- Reverse camera, sorted: camera format and wiring on your Brummstadt unitEvery camera setting and check, for the Brummstadt camera or your factory one. Video, 8:28.
- Clear calls on your Brummstadt unit: fitting the mic and the mic settingsIf you fitted the external mic: pick External Mic and set the mic gain. Video, 8:30.
- TPMS on your Brummstadt unitIf you added tyre pressure sensors: they talk to the unit through their own small USB receiver. Video, 8:45.
Prefer a professional fit?
Brummstadt also offers a professional fit: your kit fitted, programmed and tested at a partner workshop on the Gold Coast in Queensland or in Launceston in Tasmania. Choose Professional installation on the kit page when you order, with at least 28 days notice.
See the professional fitDid this video help?
Thank you for letting us know.
Thank you. If something was missing, ask us below.
Ask a question about this video
Your question comes straight to the Brummstadt team and is not shown on this page. We answer by email, and the questions we get help us make this video and its steps even better.
The kit in this video
Toyota HiAce 300 Series head unit kit
The kit in this video, with the 9 inch, 10.1 inch or 13.3 inch screen.
See the kitMore Toyota HiAce videos
Connect your phone to your Brummstadt unitVideo, 9:44
RAM and storage on your Brummstadt unitVideo, 8:45
TPMS on your Brummstadt unitVideo, 8:45
Reverse camera, sorted: camera format and wiring on your Brummstadt unitVideo, 8:28
The 10 m rear camera extension cable: connecting it and routing itVideo, 1:32
Clear calls on your Brummstadt unit: fitting the mic and the mic settingsVideo, 8:30
How to update your Brummstadt head unit onlineVideo, 8:28
Full transcript
- Viewer: Can a big Android screen really go into my HiAce? Will my climate knobs and my hazard switch still work? And which of the two dash options is mine?
- Narrator: Yes, it fits. Today you'll put a Brummstadt screen into your Toyota HiAce, the three hundred series that arrived in twenty nineteen, and it'll look like it came from the factory.
- Narrator: Your climate knobs stay and look out through the new frame, your hazard switch stays put, and your parking sensors keep working on their own.
- Narrator: Is it your first time? Then give yourself one to three hours. Have you done this before? Then it's often done in under an hour. Put the kettle on, there's no rush.
- Narrator: Watch it once to the end first, because the end holds a few extra tips. Then start again and follow along, pausing whenever you like.
- Narrator: Here's the plan. We find your option, get ready, remove the factory head unit and fit the frame. We do the wiring and plugs, set up the CAN box and the steering wheel buttons, and add the reverse camera. Then we power up, test it all, and close it up.
- Narrator: On our product page, your HiAce asks for its factory dashboard layout, and there are two. One is called Dashboard with rear climate controls, and the other is Dashboard with open lower center area. Here they are side by side.
- Narrator: Look just below your three climate knobs and the row of small switches. Is there a second panel there with two more knobs, marked rear, cooler and heater? Then yours is the Dashboard with rear climate controls.
- Narrator: Don't let the little word rear on your left knob fool you. That's the switch for the rear demister, and it's on both dashes. What decides it is what sits under your knobs.
- Narrator: Is that area open instead, with a small tray under the switches and space below it? Then yours is the Dashboard with open lower center area.
- Narrator: Take a photo of your own dash and hold it next to these two pictures. Whether you drive the long van, the crew van, the super long van or the Commuter, the shape under your knobs is what decides it.
- Viewer: Which screen size do I need, then? I saw three sizes on the page.
- Narrator: The screen size follows your layout. With rear climate controls it's the nine inch, and with the open lower center area it's the ten point one inch. Each one comes in its own frame, made for that dash.
- Narrator: The two frames look alike at first glance, so check your layout before you start. The nine inch frame is shaped around the rear climate controls, and the ten point one inch frame is shaped for the open area. Hold a frame against the other dash, and it won't fit around your knobs.
- Narrator: Did you pick the thirteen point three inch? It fits both layouts. It's a big screen that sits out in front of the dash, rather than flush in it.
- Narrator: On some dashes it covers part of the air vents or the hazard switch. So hold the screen up to your dash and have a good look from the driver's seat before you start.
- Narrator: Here's what's in your box. You'll find your Brummstadt screen with the frame for your layout, and the plug-in harness. There's also a small CAN box for your steering wheel buttons. The harness is the same for both layouts, and only the screen and the frame change.
- Narrator: Any camera, microphone or other extras you picked come in the same box, and we'll fit each one in its own step.
- Narrator: The memory and storage version you picked doesn't change a single step. To see what it gives you, tap here for our RAM and storage film.
- Narrator: At the end, this is what sits in your HiAce. There's a big bright screen in a black frame that matches your dash, with your own climate knobs right below it, and a harness that plugs into your car's own plugs. Nothing in the dash gets cut.
- Narrator: One thing changes. If your HiAce shows navigation arrows between the dials, those came from the factory navigation, so they won't show there any more. Your maps run on the big screen instead.
- Narrator: Is your HiAce a Japanese import that still has the older shape, with the flat nose and the older dash, even if it was built after twenty nineteen? Then it takes our kit for the older HiAce, and that one has its own film. Tap here for it.
- Narrator: And do you drive a Toyota Granvia from twenty nineteen? Then this kit and this film are made for it too.
- Narrator: If your dash looks different from both pictures, put your photo next to them before you take anything apart, and compare them shape by shape.
- Narrator: Our one rule for the whole install is feel, not force. If something won't move, there's a reason, and we'll show you what it is.
- Narrator: Lay every part out on a towel first, so anything missing shows up now and not halfway through. Put another towel on the passenger seat for the parts you'll take off.
- Narrator: You'll need plastic trim tools and a Phillips screwdriver. Add a spanner for the battery clamp and a few cable ties. If you're fitting a camera, a multimeter makes it easy, and if you ticked the trim removal tools, they're already in your box.
- Narrator: Why do we use plastic tools? Because a metal screwdriver leaves marks in the soft trim for good. A plastic tool slides in, and the panel comes away clean.
- Narrator: Take a photo of your dash now, and later another of the back of the old head unit before you unplug anything. Those photos let you compare every plug in a moment.
- Narrator: Last, try the old system once. Play the radio, press the buttons on your steering wheel and look at the reverse camera. Then listen to the parking sensors and flash the hazards, so you know what normal looks like.
- Narrator: Next is the battery. Switch the ignition and the lights off, then undo the negative terminal, the one marked minus, and tuck the lead aside in a cloth.
- Viewer: Do I really need to? It's only a radio.
- Narrator: That's a fair question. With the battery connected, a bare pin touching metal can blow a fuse, and then the screen stays dark on the day. A minute with a spanner saves you an afternoon.
- Narrator: Here's how your HiAce dash is built. The factory screen and your three climate knobs sit together in one black centre panel. The light surround around it stays in the car, and so does your hazard switch, up at the top by the driver's vent.
- Narrator: Factory screens differ by year, so yours may look a little different from the one shown here. Go by the shape of the black panel, and take it slowly.
- Narrator: On an automatic, the gear selector sits right beside the panel, so work carefully around it. On a manual, the gear stick comes up from the floor and stays out of the way.
- Narrator: Start at the bottom edge of the black panel. Slide a plastic tool into the gap, and ease the panel out until the first clips let go.
- Narrator: Then work up both sides, one clip at a time, with the tool right next to each clip.
- Narrator: Lever in one spot, or yank the whole panel at once, and a clip snaps or the plastic cracks, and then that panel rattles for good. Go clip by clip, and each one lets go with a small pop.
- Narrator: If there's a narrow strip along the top of the screen that lifts away on its own, ease it off first. Then the whole panel, with the screen and the knobs, comes towards you.
- Narrator: It's still connected behind, so stop as soon as you see wires. Pull it further, and a lead can come out of its plug.
- Narrator: Reach behind and unplug your climate knobs. Press the tab first, then pull the plug body, never the wires.
- Viewer: Does the hazard switch come out with it?
- Narrator: No, it doesn't. It sits in the light surround above the driver's vent, and it stays right there, plugged in and working.
- Narrator: Now let's take out the factory head unit itself. It sits in a metal frame behind the panel, held by screws on both sides. Undo them, and tape each screw to a piece of paper, so none gets lost behind the dash.
- Narrator: Slide it forward just far enough to reach the back, then unplug each plug. Press the tab first, then pull the plug body.
- Narrator: Pull on the wires instead, and a thin lead can tear out of its plug, with no slack left to fix it. Press the tab, pull the body, and it slides out easily.
- Narrator: The old head unit's out. Keep it boxed with its screws, in case you ever sell the HiAce.
- Narrator: Your new Brummstadt frame has three round openings, and your climate knobs look out through them. Compare the back of your old panel with your new frame, and fit the climate unit the same way it was held, snug and gentle. Keep the old panel until the knobs work in the new frame.
- Narrator: Before anything gets screwed in, hold your new frame up to the dash, with nothing plugged in yet. This trial fit takes a minute, and it tells you everything.
- Narrator: With the nine inch frame, your climate knobs look out through its three round openings, and your rear climate controls look out through the opening below them.
- Narrator: With the ten point one inch frame, the frame fits around your knobs and the open area below, and your small tray stays right where it was.
- Narrator: With the thirteen point three inch, sit in the driver's seat and check that the screen clears your vents and your hazard switch, before you fix anything.
- Narrator: Keep the screws snug, not tight. If you over-tighten them, the metal screw cuts into the plastic frame, the frame bends, and then it won't sit flush again. Hand tight with a screwdriver is plenty.
- Narrator: If the frame doesn't line up with your knobs, stop there, and check your layout against the two pictures again. Forcing a frame into place cracks the plastic, and a cracked frame never looks right again.
- Narrator: Now it's time for the plugs. Your Brummstadt harness is the same for both layouts, and it has a partner for each of your car's radio plugs. Every one has its own shape, like a kids' shape puzzle.
- Narrator: Before you click anything in, hold the harness plugs next to the car's plugs, and compare them with your photo. They should match, shape for shape.
- Narrator: If a plug doesn't match its partner, stop, and don't force it, because a bent pin never answers again. Compare the shapes one by one, and find the partner that fits.
- Narrator: Push until it clicks, then give the plug body a gentle tug. A half-latched plug drops out on the first bumpy road and takes the sound or the screen with it.
- Narrator: If your box has two harnesses, and the screen stays dark with the key on, turn the ignition off, then swap to the other one.
- Viewer: I've got plugs left over. Did I miss something?
- Narrator: That's normal. Your Brummstadt unit brings its own GPS and Bluetooth, and its own microphone too, so the car's plugs for those have no partner. Tape them up and tuck them away.
- Narrator: If your HiAce has a factory amplifier, compare its plugs with your harness, shape by shape. Leave any plug without a partner unplugged, and test the sound before you close up.
- Narrator: Your car's aerial plug goes into the aerial lead on your harness, and that lead goes into the round radio socket on the back of the unit.
- Narrator: Your GPS aerial plugs into the socket marked GPS. Put it up on top of the dash, under the plastic and away from metal, so it can see the sky.
- Narrator: Your unit's USB leads come out at the back, so run the one for your phone forward to a spot you can reach, like the tray. Use a separate charger for your phone, because these USB leads don't charge it.
- Narrator: Did you order the external microphone? Plug it into the small round socket marked MIC on the bundle of round plugs. Its lead is three metres long, so run it up the windscreen pillar and stick the mic on the roof lining beside the driver's sun visor, away from the vents, so callers hear you and not the road. Tap here for our full microphone film.
- Narrator: Does your unit have a SIM holder? Fit your SIM now while everything's in your hands, and the unit gets mobile data without your phone.
- Narrator: Did you pick DAB plus? The DAB module runs from a USB lead on the unit, and its strip aerial goes on the windscreen. Tap here for more on DAB.
- Narrator: Did you pick the dash camera? It connects by USB, and you watch its footage right on the screen. And if you picked tyre pressure sensors, they talk to the unit through their own small USB receiver. Tap here for our tyre pressure film.
- Narrator: The OBD2 tool from your box plugs into the diagnostic port under the dashboard. It talks to the unit or your phone over Bluetooth, and it shows live engine data and fault codes.
- Narrator: Then cable-tie the long leads together and to the car's own wiring. Loose leads rattle behind the dash, and in time an edge can rub through the insulation and cause a short. A few ties keep it quiet and safe.
- Narrator: Your HiAce talks to the screen through the small CAN box in your kit. It passes on your steering wheel buttons and some car information, like an open door.
- Narrator: The CAN box has a short data lead with a small plug. Push it into its socket on the back of the unit, while the battery's still off.
- Viewer: And if the screen works, but the steering wheel buttons do nothing?
- Narrator: Then look at that short data lead first. One owner's buttons did nothing until that small plug was pushed all the way home, and then every button answered.
- Narrator: After the first power-up, you'll pick your car in the unit's settings. Open My Car, then Diagnosis, then Car, and pick the maker that's printed on your CAN box.
- Narrator: Your HiAce isn't in that list by name, so pick a Toyota entry, and then press every button on your wheel. If one doesn't answer, go back and try the next Toyota entry, until they all work.
- Narrator: Here's a quick check that the entry is right: open a door, and the screen shows a little picture of the open door.
- Narrator: Now let's sort out the reverse camera. Here are the key steps for your HiAce, and our full camera film has every setting and check. Tap here for it.
- Narrator: Every three hundred series HiAce came with a reversing camera. It can keep working on your new screen if it runs on twelve volts, and the guide lines then come from your Brummstadt unit.
- Narrator: So measure it before you plug it in. With the car in reverse, a meter on the camera's power wire should show twelve volts. If it reads about six volts, a twelve to six volt step-down module in its power lead, or the Brummstadt camera, is the way.
- Narrator: Some HiAce models have a digital rear-view mirror with its own camera. Leave its wiring as it is, and test it in reverse before you close up.
- Viewer: My van's a long one. Will the camera cable reach?
- Narrator: Measure it first. The camera cable in your kit is three metres long, and a long HiAce is more than five metres from end to end, so the route from the back door to the dash is much longer. Run a string the way the cable will go, and if it's short, the ten metre extension cable sorts it.
- Narrator: Mount the Brummstadt camera on the back of the van, centred above the number plate. Run its lead inside along the roof lining or under the floor trim, through a rubber grommet, never over a sharp edge. Your parking sensors keep beeping just as before.
- Narrator: Camera power comes from the reverse light. Its trigger wire goes to the reverse light's positive wire, and the black one goes to bare metal. With a meter, you want twelve volts in reverse and nothing in park.
- Narrator: Put the trigger on the indicator wire, and the camera jumps on every time you indicate. Check with the meter first, and the camera only comes up in reverse.
- Narrator: At the dash, the camera's yellow video plug goes into the yellow camera socket on the harness. Then the picture comes up as soon as you select reverse.
- Narrator: Did you order the front camera as well? Its lead plugs into the fifth white socket on the back of the unit, and you switch on Double recording in the settings, so both cameras work. Our camera film shows each step.
- Narrator: Now it's time to wake it up. Reconnect the negative terminal, snug the nut, and turn the ignition on. You'll see the Brummstadt logo, and then the home screen.
- Narrator: If the screen stays black, take the battery off again and check that the main plug has really clicked. A plug that's nearly in is the first thing to check.
- Narrator: If you ever notice a hot plug or a burning smell, switch the ignition off and disconnect the battery straight away, and check that plug before you power up again.
- Narrator: Now set your car in My Car, Diagnosis and Car, just as we showed you, and press every steering wheel button to test it.
- Narrator: If there's no sound, the CAN list is rarely the reason. Check that the main plug is clicked fully home, then check the volume, and play a song from your phone.
- Narrator: For the radio, set the radio region to Australia. If stations are weak, raise the FM sensitivity in the radio settings, one step at a time.
- Narrator: Now let's set up the camera. Shift into reverse with your foot on the brake. No signal is a good sign: the screen has seen reverse. Now hold your finger on the picture until a box pops up. Pick AHD ten eighty P, twenty five hertz for the Brummstadt camera, or the format your factory camera needs, usually DSV, and then tap save.
- Narrator: If you fitted the external mic, pick External Mic in the settings and set the mic gain to seven, just as our microphone film shows step by step.
- Narrator: For your phone, open Zed-Link, the app for CarPlay and Android Auto. Pair over Bluetooth for wireless, or plug in a data cable. Tap here for our phone film.
- Narrator: When it all works, take a photo of each settings screen, so you can set it back quickly after an update.
- Viewer: It works! Can I put it all back together now?
- Narrator: You nearly can, but not quite yet. Let's do ten minutes of testing first, because a fix takes seconds while the dash is open, and an evening once it's closed.
- Narrator: Touch the screen everywhere, play a song you know and change the volume, and try a radio station you know.
- Narrator: Press every steering wheel button. Make a real call, both ways, so you hear the microphone. Then connect your phone and start CarPlay or Android Auto.
- Narrator: With your foot on the brake, select reverse, and the camera comes up. Out of reverse, your normal screen is back. Then try the indicators, left and right, and the screen should stay put.
- Narrator: Back up slowly towards something soft, and the parking sensors should beep just as before. Then glance at the instrument cluster: there shouldn't be any new warning message.
- Narrator: If a warning does come up, switch off and check that every plug you touched is fully home, then test again before you close anything.
- Narrator: Switch the headlights on and check that the screen is still easy to read. Then press the hazards: they flash just like before.
- Narrator: Turn the ignition off and on again, and your settings should still be there. If something isn't right, go back to its plug or its setting. It's nearly always one of those two.
- Narrator: Is it all working? That's lovely. Switch the ignition off, and take the battery off again, so nothing's live while the leads move.
- Narrator: Feed the harness in behind the unit, every lead clear of edges and screw holes, and slide the screen and frame home where the black panel was.
- Narrator: If the frame won't sit flat, something's caught behind it. Don't force it down, because that would crush a lead and bend the frame. Lift it, free the lead, and it sits flat on its own.
- Narrator: Now fix your frame in place with the fixings from your kit, snug and gentle, never forced. If you lifted off the narrow strip along the top, press it back on now, clip by clip.
- Narrator: Put the battery back on for one last round. Listen to the sound, press the buttons, and check the camera and the hazards, because closing up can nudge a plug.
- Narrator: The battery was off, so set the clock if it needs it. It only takes a minute, and then you're done.
- Narrator: That's it. You've fitted a Brummstadt screen to your HiAce yourself. The kettle's gone cold, but you've earned a fresh cup.
- Narrator: Let's look back. You found your option, removed the factory head unit and fitted the frame. You did the wiring and plugs, set up the CAN box and the steering wheel buttons, and added the reverse camera. Then you powered up, tested it all, and closed it up.
- Narrator: Here's an extra tip: keep your settings photos in the glovebox. If anything ever needs a tweak, you've got everything in one place.
- Narrator: Everything in this film we learned from our own installs, our installers and lots of HiAce owners. Every one of their stories made it better.
- Narrator: Do you still have a question, or an idea for your HiAce? Ask your installer, or better still, have a yarn with us at Brummstadt. We work with these units every day, and even good installers sometimes haven't met these settings yet, which is no fault of theirs.
- Narrator: We want every HiAce owner to get it right the first time, which is why our films go this deep.
- Narrator: Now, can I ask a small favour? Before you bought, you probably read a few reviews, and somebody's five stars helped you decide.
- Narrator: If you're still deciding, good on you, you'll love it. And if you've just fitted it yourself, and this film saved you a support message and an afternoon, you're probably thinking we've earned our five stars.
- Narrator: It's one click on the review button right here, quicker than talking one stubborn clip back into its hole, and it tells the next HiAce owner they're in good hands. Enjoy the drive.
If you have still got a question about your HiAce, ask us at Brummstadt. We sell these kits and work with them every day.