Fit your Brummstadt screen to a Toyota Prado 150 (2009 to 2022)
Fit the Brummstadt screen to your Prado 150 yourself, one step at a time, and test everything while the dash is still open.
- Time
- Ten and a half minutes to watch, with every step also written out below.
- Have ready
- Plastic trim tools, a screwdriver, a socket set, a towel for the dash and a cup for the screws.
- Three different dashes
- There are three different Prado 150 dashes, and each one comes apart a little differently. Go by the dash, not the year on the papers.
- How to watch
- Watch it once to the end, then start again and follow along.
Does this video fit your car?
One video for the three Prado 150 dashes. Check these points before you start.
- Your dash
- The earlier Prado 150 has a small trip computer screen on top, with buttons like DISP and RESET, and a CD radio with number buttons underneath. The facelifted Prado 150 has one touchscreen in a silver surround, with APPS and AUDIO buttons on the left. The latest Prado 150 has a new dash: a touchscreen with two round knobs, and a flat climate panel right under it.
- Years
- Our three kits are the Prado 150 2009 to 2013 for the earlier dash, 2014 to 2017 for the facelifted dash and 2018 to 2022 for the latest dash. Close to the facelift? Go by the dash, not the year on the papers: if your car already has the touchscreen with APPS and AUDIO, it takes the facelifted kit.
- Grade
- For the facelifted and the latest dash, the kit is made for the Base Model and the GXL. Altitude, VX and Kakadu have a factory premium audio and camera system that needs a different kit, so they show as not available yet.
- Premium audio and sat nav
- You can spot a premium dash by a JBL badge on the screen or the speaker grilles, factory sat nav buttons like MAP and DEST, a roof DVD screen, or cameras that show all around the car. Some GXLs also have a factory amplifier, a box under a front seat.
- Screen size
- The earlier dash takes a 9 inch screen, the facelifted and latest dashes a 10.1 inch, and both sit flush in the kit frame. The 13.3 inch screen sits out from the dash instead of flush, and in some cars it covers part of the air conditioning controls, the hazard switch or an air vent. On the earlier dash, the climate panel meets its bottom edge, so the 9 inch is the easier fit there.
- Earlier dash: trip computer
- The extra frame keeps your trip computer, moved from the top of the dash to the lower position, so you still see fuel use, range and temperature. On many earlier cars the factory reverse camera shows on that small screen too. Without the extra frame, the small screen comes out, and its camera picture with it.
- Earlier dash: hazard switch
- The kit frame has its hazard switch opening on the left. If the factory lead doesn't reach, the switch fits upside down.
- Steering wheel buttons and climate
- The CAN box reads your Prado's data, like the wheel buttons and the climate. Until its small 8-pin lead clicks into the unit, the wheel buttons and the climate readout stay quiet. If the wheel buttons don't work straight away, they can be taught on the screen.
- Factory camera
- On the Base Model and the GXL, a single factory reverse camera can stay, through the reverse adapter with the 24-pin plug. Factory cameras and our cameras don't mix, so choose one or the other. Some Toyota factory cameras run on about 6 volts; an auto electrician can fit a small step-down module, so you keep your factory camera.
- Not in this video
- Altitude, VX and Kakadu with the factory premium audio and camera system need a different kit, not available yet. The factory cameras that show all around the car belong to the premium system, and they don't show on this screen.
What you need
- Tools
- Plastic trim tools
- A screwdriver
- A socket set
- A towel for the dash
- A cup for the screws
- In the box
- The screen with its frame
- The main harness with Toyota plugs
- The CAN box with its small 8-pin lead
- The reverse camera adapter, the one with the 24-pin plug
- The radio booster and aerial adapter
- The GPS aerial
- USB leads
- The microphone and the RCA lead
- The test harness, to try the screen on its own
- Earlier dash: the extra frame for the trip computer, if you chose it
Optional parts
Each one has its own page.
- Trim removal toolsFour plastic pieces that take the trim off without scratches.
- Rear cameraAHD 1080p reverse camera with night vision. Factory cameras and our cameras don't mix, so choose one or the other.
- DAB+ digital radio adapterDigital radio with its own aerial, plugged into the unit.
- Tyre pressure sensors (TPMS)Kits with 4 or 8 sensors, external or internal. Internal sensors are fitted at a tyre shop. Plug in the USB receiver first, then fit the sensors.
- OBD2 diagnostic toolA Bluetooth reader for the diagnostic port, with its own app.
Step by step
The same steps as the video. Each one plays from its own spot.
Which option is yours
Play from 0:50- Start with your dash. The earlier Prado 150 has a small trip computer screen on top, with buttons like DISP and RESET, and a CD radio with number buttons underneath.
- The facelifted Prado 150 has one touchscreen in a silver surround, with APPS and AUDIO buttons on the left.
- The latest Prado 150 has a new dash: a touchscreen with two round knobs, and a flat climate panel right under it.
- Close to the facelift? Go by the dash, not the year on the papers. If your car already has the touchscreen with APPS and AUDIO, it takes the facelifted kit.
- Next, your grade. For the facelifted and the latest dash, the kit is made for the Base Model and the GXL.
- Altitude, VX and Kakadu have a factory premium audio and camera system that needs a different kit, so they show as not available yet.
- You can spot a premium dash by a JBL badge on the screen or the speaker grilles, factory sat nav buttons like MAP and DEST, a roof DVD screen, or cameras that show all around the car.
- Some GXLs also have a factory amplifier, a box under a front seat.
- Then the screen size. The earlier dash takes a 9 inch screen, the facelifted and latest dashes a 10.1 inch, and both sit flush in the kit frame.
- There's also a 13.3 inch screen. It sits out from the dash instead of flush, and in some cars it covers part of the air conditioning controls, the hazard switch or an air vent.
- On the earlier dash, the climate panel meets the bottom edge of the 13.3 inch screen, so the 9 inch is the easier fit there.
- For the earlier dash there's one more option: the extra frame. It keeps your trip computer, moved from the top of the dash to the lower position, so you still see fuel use, range and temperature.
- On many earlier cars the factory reverse camera shows on that small screen too. Without the extra frame, the small screen comes out, and its camera picture with it.
Before you start
Play from 3:11- Before you take the old unit out, set the fader and balance to the centre on the factory radio. It takes a moment, and it helps the rear speakers later.
- Lay out plastic trim tools, a screwdriver, a socket set, a towel for the dash and a cup for the screws.
- Disconnect the negative battery terminal, so no fuse blows while plugs are apart.
- Take a photo of each plug before you unplug it. It makes the new wiring easier.
Take out the factory unit
Play from 3:47- Each Prado dash comes apart a little differently, so take your time. Ease the trim around the screen off with plastic tools, without forcing it.
- Undo the screws that hold the factory unit, ease it forward and unplug everything at the back.
- On the earlier dash, the top screen is only a display. The radio module with the plugs sits lower down, and its car plugs are the ones the new harness connects to.
- Some factory plugs stay empty afterwards, like the factory GPS, microphone or USB. That's normal.
Fit the frame
Play from 4:30- Move the factory vents across to the kit frame.
- Fit the kit's brackets to the screen, then offer the frame up to the dash, but leave it loose for now.
- On the earlier dash with the extra frame, the trip computer goes into it, below the new screen.
Hazard switch on the earlier dash
Play from 4:53- On the earlier dash, the kit frame has its hazard switch opening on the left.
- Move the hazard switch from the factory surround into that opening.
- If the factory lead doesn't reach, fit the switch upside down.
- If it's a tight fit, smooth the edges of the opening lightly with fine sandpaper.
Wiring and plugs
Play from 5:21- Now the wiring. Match each kit plug to the car plug of the same shape, and press until it clicks.
- If a kit plug and a car plug don't match at all, stop there. Never force a plug.
- The big power plug goes into the back of the screen.
- The radio booster goes between the car's aerial lead and the ANT socket, with the aerial adapter on the car side.
- The GPS aerial goes in the GPS socket. Place it under the dash top, where it can see the sky.
- USB leads go into their 4 pin and 6 pin sockets.
- The microphone plugs into the RCA lead at MIC. We'll mount it after power-up.
CAN box and the 8-pin lead
Play from 6:14- The CAN box reads your Prado's data, like the wheel buttons and the climate.
- Plug the CAN box into its plug on the harness.
- The small CAN lead goes into its own 8-pin socket on the unit. Until it clicks, the wheel buttons and the climate readout stay quiet.
- If the wheel buttons don't work straight away, they can be taught on the screen: start the learning, press the button on the wheel first, then tap the matching icon, and end the learning when you're done.
Reverse camera
Play from 6:52- On the Base Model and the GXL, a single factory reverse camera can stay. The reverse adapter in the harness, the one with the 24-pin plug, connects it.
- Factory cameras and our cameras don't mix, so choose one or the other.
- The factory cameras that show all around the car belong to the premium system, and they don't show on this screen.
- On the earlier dash, the factory camera stays with the small screen, so it needs the extra frame.
- No signal is a good sign: the screen has seen reverse. Usually the camera format just needs to match. Our reverse camera video shows how to set it.
- Some Toyota factory cameras run on about 6 volts, so they can't take 12 volts straight from the screen. An auto electrician can fit a small step-down module, so you keep your factory camera.
First power-up and settings
Play from 7:51- Reconnect the battery and turn the key. The Brummstadt logo comes up, then the home screen.
- Nothing at all? Check the big power plug is fully in, then the car's fuses.
- You can also try the screen on its own with the test harness from the kit: red and yellow to positive, black to negative.
- The screen usually comes set up for your Prado already.
- If the door picture shows the wrong door open, first check that the CAN box and its 8-pin lead are plugged in. Then swap it: MyCar, Door window setting, Exchange the front door. On the screen this switch reads FDoor exchange.
- For calls, mount the microphone up near the mirror, then switch the screen to the external microphone. Our microphone video shows where.
Test before closing
Play from 8:47- Test everything now, while the dash is still open.
- Press each button on the wheel and watch the screen answer.
- Run the climate: on most cars, the readout pops up at the bottom of the screen.
- Open a door and check the door picture.
- Select reverse: the camera picture comes up.
- On the earlier dash, press the hazard switch: it clicks, springs back, and the indicators flash. Press again to stop.
- Play a song you know, and change the volume.
- Tune the radio and check the reception.
- Connect your phone for Apple CarPlay or Android Auto. If it won't connect, our phone video helps.
- Rear parking sensors quiet? A sensor switch may have come unplugged while the dash was apart. Plug it back in.
- TPMS and OBD2 are add-ons with their own app. For TPMS, plug in the USB receiver first, then fit the sensors.
Closing up and done
Play from 10:02- All good? Tidy the wires behind the screen so nothing gets pinched, slide the unit home and fasten the frame.
- Clip the trim back on, and you're done.
Questions from customers
Questions Prado 150 owners asked us, answered in the video.
Which kit fits my Prado 150, and what if my car is close to the facelift?
Go by the dash, not the year on the papers. The earlier Prado 150 has a small trip computer screen on top and a CD radio with number buttons underneath. The facelifted Prado 150 has one touchscreen in a silver surround, with APPS and AUDIO buttons on the left. The latest Prado 150 has a new dash: a touchscreen with two round knobs, and a flat climate panel right under it.
If your car already has the touchscreen with APPS and AUDIO, it takes the facelifted kit.
See it in the video at 0:53Does the kit suit an Altitude, VX or Kakadu?
For the facelifted and the latest dash, the kit is made for the Base Model and the GXL. Altitude, VX and Kakadu have a factory premium audio and camera system that needs a different kit, so they show as not available yet.
You can spot a premium dash by a JBL badge on the screen or the speaker grilles, factory sat nav buttons like MAP and DEST, a roof DVD screen, or cameras that show all around the car.
See it in the video at 1:35Will the 13.3 inch screen fit my dash?
The earlier dash takes a 9 inch screen, the facelifted and latest dashes a 10.1 inch, and both sit flush in the kit frame.
The 13.3 inch screen sits out from the dash instead of flush, and in some cars it covers part of the air conditioning controls, the hazard switch or an air vent. On the earlier dash, the climate panel meets the bottom edge of the 13.3 inch screen, so the 9 inch is the easier fit there.
See it in the video at 2:13Do I keep the trip computer on the earlier dash?
Yes, with the extra frame. It keeps your trip computer, moved from the top of the dash to the lower position, so you still see fuel use, range and temperature.
On many earlier cars the factory reverse camera shows on that small screen too. Without the extra frame, the small screen comes out, and its camera picture with it.
See it in the video at 2:46On my earlier dash, the hazard switch lead does not reach the new frame. What now?
On the earlier dash, the kit frame has its hazard switch opening on the left. Move the hazard switch from the factory surround into that opening.
If the factory lead doesn't reach, fit the switch upside down. If it's a tight fit, smooth the edges of the opening lightly with fine sandpaper.
See it in the video at 4:56Do my steering wheel buttons still work?
The CAN box reads your Prado's data, like the wheel buttons and the climate. The small CAN lead goes into its own 8-pin socket on the unit. Until it clicks, the wheel buttons and the climate readout stay quiet.
If the wheel buttons don't work straight away, they can be taught on the screen: start the learning, press the button on the wheel first, then tap the matching icon, and end the learning when you're done.
See it in the video at 6:17Can I keep my factory reversing camera?
On the Base Model and the GXL, a single factory reverse camera can stay. The reverse adapter in the harness, the one with the 24-pin plug, connects it. On the earlier dash, the factory camera stays with the small screen, so it needs the extra frame.
Factory cameras and our cameras don't mix, so choose one or the other. The factory cameras that show all around the car belong to the premium system, and they don't show on this screen.
See it in the video at 6:55The screen stays dark when I turn the key. What do I check?
Check the big power plug is fully in, then the car's fuses.
You can also try the screen on its own with the test harness from the kit: red and yellow to positive, black to negative.
See it in the video at 8:01After fitting
Once the screen is in and tested, these videos help you set up the rest. The installation video points to most of them along the way.
- Connect your phone to your Brummstadt unitApple CarPlay or Android Auto, and what to do if your phone won't connect. Video, 9:44.
- Reverse camera, sorted: camera format and wiring on your Brummstadt unitMatching the camera format, for a factory camera or ours. Video, 8:28.
- Clear calls on your Brummstadt unit: fitting the mic and the mic settingsWhere the microphone goes, and switching the screen to the external microphone. Video, 8:30.
- TPMS on your Brummstadt unitIf you added tyre pressure sensors: the USB receiver goes in first, then the sensors. Video, 8:45.
Did this video help?
Thank you for letting us know.
Thank you. If something was missing, ask us below.
Ask a question about this video
Your question comes straight to the Brummstadt team and is not shown on this page. We answer by email, and the questions we get help us make this video and its steps even better.
The kits in this video
Toyota Prado 150 head unit kits
One video for the three Prado 150 kits: 2009 to 2013, 2014 to 2017 and 2018 to 2022. Find the kit for your car.
Find your vehicleMore Toyota Prado videos
Connect your phone to your Brummstadt unitVideo, 9:44
RAM and storage on your Brummstadt unitVideo, 8:45
TPMS on your Brummstadt unitVideo, 8:45
Reverse camera, sorted: camera format and wiring on your Brummstadt unitVideo, 8:28
The 10 m rear camera extension cable: connecting it and routing itVideo, 1:32
Clear calls on your Brummstadt unit: fitting the mic and the mic settingsVideo, 8:30
How to update your Brummstadt head unit onlineVideo, 8:28
Full transcript
- Narrator: This is the Toyota Prado 150. Let's fit a big Brummstadt screen with Apple CarPlay and Android Auto, and keep the things you use every day, like your wheel buttons and, on most cars, your reverse camera.
- Narrator: There are three different Prado 150 dashes, so first we'll find yours.
- Narrator: Here's what's in the box: the screen with its frame, the main harness with Toyota plugs, the CAN box with its small 8-pin lead, the reverse camera adapter, the radio booster and aerial adapter, the GPS aerial, USB leads, the microphone and the RCA lead.
- Narrator: Then we take out the old unit, plug in the kit, set it up, and test everything before the dash goes back together.
- Narrator: Start with your dash. The earlier Prado 150 has a small trip computer screen on top, with buttons like DISP and RESET, and a CD radio with number buttons underneath.
- Narrator: The facelifted Prado 150 has one touchscreen in a silver surround, with APPS and AUDIO buttons on the left.
- Narrator: The latest Prado 150 has a new dash: a touchscreen with two round knobs, and a flat climate panel right under it.
- Narrator: Close to the facelift? Go by the dash, not the year on the papers. If your car already has the touchscreen with APPS and AUDIO, it takes the facelifted kit.
- Narrator: Next, your grade. For the facelifted and the latest dash, the kit is made for the Base Model and the GXL.
- Narrator: Altitude, VX and Kakadu have a factory premium audio and camera system that needs a different kit, so they show as not available yet.
- Narrator: You can spot a premium dash by a JBL badge on the screen or the speaker grilles, factory sat nav buttons like MAP and DEST, a roof DVD screen, or cameras that show all around the car.
- Narrator: Some GXLs also have a factory amplifier, a box under a front seat.
- Narrator: Then the screen size. The earlier dash takes a 9 inch screen, the facelifted and latest dashes a 10.1 inch, and both sit flush in the kit frame.
- Narrator: There's also a 13.3 inch screen. It sits out from the dash instead of flush, and in some cars it covers part of the air conditioning controls, the hazard switch or an air vent.
- Narrator: On the earlier dash, the climate panel meets the bottom edge of the 13.3 inch screen, so the 9 inch is the easier fit there.
- Narrator: For the earlier dash there's one more option: the extra frame. It keeps your trip computer, moved from the top of the dash to the lower position, so you still see fuel use, range and temperature.
- Narrator: On many earlier cars the factory reverse camera shows on that small screen too. Without the extra frame, the small screen comes out, and its camera picture with it.
- Narrator: Before you take the old unit out, set the fader and balance to the centre on the factory radio.
- Narrator: It takes a moment, and it helps the rear speakers later.
- Narrator: Lay out plastic trim tools, a screwdriver, a socket set, a towel for the dash and a cup for the screws.
- Narrator: Disconnect the negative battery terminal, so no fuse blows while plugs are apart.
- Narrator: And take a photo of each plug before you unplug it. It makes the new wiring easier.
- Narrator: Each Prado dash comes apart a little differently, so take your time. Ease the trim around the screen off with plastic tools, without forcing it.
- Narrator: Undo the screws that hold the factory unit, ease it forward and unplug everything at the back.
- Narrator: On the earlier dash, the top screen is only a display. The radio module with the plugs sits lower down, and its car plugs are the ones the new harness connects to.
- Narrator: Some factory plugs stay empty afterwards, like the factory GPS, microphone or USB. That's normal.
- Narrator: Move the factory vents across to the kit frame.
- Narrator: Fit the kit's brackets to the screen, then offer the frame up to the dash, but leave it loose for now.
- Narrator: On the earlier dash with the extra frame, the trip computer goes into it, below the new screen.
- Narrator: On the earlier dash, the kit frame has its hazard switch opening on the left.
- Narrator: Move the hazard switch from the factory surround into that opening.
- Narrator: If the factory lead doesn't reach, fit the switch upside down.
- Narrator: If it's a tight fit, smooth the edges of the opening lightly with fine sandpaper.
- Narrator: Now the wiring. Match each kit plug to the car plug of the same shape, and press until it clicks.
- Narrator: If a kit plug and a car plug don't match at all, stop there. Never force a plug.
- Narrator: The big power plug goes into the back of the screen.
- Narrator: The radio booster goes between the car's aerial lead and the ANT socket, with the aerial adapter on the car side.
- Narrator: The GPS aerial goes in the GPS socket. Place it under the dash top, where it can see the sky.
- Narrator: USB leads go into their 4 pin and 6 pin sockets.
- Narrator: The microphone plugs into the RCA lead at MIC. We'll mount it after power-up.
- Narrator: The CAN box reads your Prado's data, like the wheel buttons and the climate.
- Narrator: Plug the CAN box into its plug on the harness.
- Narrator: The small CAN lead goes into its own 8-pin socket on the unit. Until it clicks, the wheel buttons and the climate readout stay quiet.
- Narrator: If the wheel buttons don't work straight away, they can be taught on the screen: start the learning, press the button on the wheel first, then tap the matching icon, and end the learning when you're done.
- Narrator: On the Base Model and the GXL, a single factory reverse camera can stay. The reverse adapter in the harness, the one with the 24-pin plug, connects it.
- Narrator: Factory cameras and our cameras don't mix, so choose one or the other.
- Narrator: The factory cameras that show all around the car belong to the premium system, and they don't show on this screen.
- Narrator: On the earlier dash, the factory camera stays with the small screen, so it needs the extra frame.
- Narrator: No signal is a good sign: the screen has seen reverse. Usually the camera format just needs to match. Our reverse camera video shows how to set it.
- Narrator: Some Toyota factory cameras run on about 6 volts, so they can't take 12 volts straight from the screen. An auto electrician can fit a small step-down module, so you keep your factory camera.
- Narrator: Reconnect the battery and turn the key. The Brummstadt logo comes up, then the home screen.
- Narrator: Nothing at all? Check the big power plug is fully in, then the car's fuses.
- Narrator: You can also try the screen on its own with the test harness from the kit: red and yellow to positive, black to negative.
- Narrator: The screen usually comes set up for your Prado already.
- Narrator: If the door picture shows the wrong door open, first check that the CAN box and its 8-pin lead are plugged in. Then swap it: MyCar, Door window setting, Exchange the front door.
- Narrator: For calls, mount the microphone up near the mirror, then switch the screen to the external microphone. Our microphone video shows where.
- Narrator: Test everything now, while the dash is still open.
- Narrator: Press each button on the wheel and watch the screen answer.
- Narrator: Run the climate: on most cars, the readout pops up at the bottom of the screen.
- Narrator: Open a door and check the door picture.
- Narrator: Select reverse: the camera picture comes up.
- Narrator: On the earlier dash, press the hazard switch: it clicks, springs back, and the indicators flash. Press again to stop.
- Narrator: Play a song you know, and change the volume.
- Narrator: Tune the radio and check the reception.
- Narrator: Connect your phone for Apple CarPlay or Android Auto. If it won't connect, our phone video helps.
- Narrator: Rear parking sensors quiet? A sensor switch may have come unplugged while the dash was apart. Plug it back in.
- Narrator: TPMS and OBD2 are add-ons with their own app. For TPMS, plug in the USB receiver first, then fit the sensors.
- Narrator: All good? Tidy the wires behind the screen so nothing gets pinched, slide the unit home and fasten the frame.
- Narrator: Clip the trim back on, and you're done.
- Narrator: Enjoy your new screen. And if anything isn't right, our team at Brummstadt is happy to help.
If you have still got a question about your Prado 150, ask us at Brummstadt. We sell these kits and work with them every day.